Bedienungsanleitung Scheppach MTP860H (Seite 26 von 64) (Deutsch, Englisch, Französisch, Polnisch)

781993

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

26 GB

4 Keep all bystanders, children, and pets at least 23m

away. If you are approached, stop the unit immedi-

ately.

5 Walk, never run with the machine.

6 This unit has a clutch. Squeeze the clutch control

lever and check that i t returns automatically to the

neutral position. If it does not, have unit adjusted by

a qualied repair personnel.

7 Disengage clutch lever before starting the engine.

8 Start the engine carefully according to instructions

and with feet well away from the tines.

9 The tines remain stationary when the clutch is disen-

gaged. If it does not, have unit adjusted by a qualied

repair personnel.

10 Always operate the machine from behind, never

pass or stand in front of the machine when the en-

gine is running.

11 Always hold the unit with both hands when operat-

ing. Keep a rm grip on the handlebars.

12 Be aware that the machine may unexpectedly

bounce upward or jump forward if the tines should

strike buried obstacles such as large stones, roots,

or stumps.

13 If the unit strikes a foreign object, stop the engine,

disconnect the spark plug, thoroughly inspect the

machine for any damage, and repair the damage be-

fore restarting and operating the machine.

14 Use extreme caution when in reverse ornpulling the

machine towards you.

15 Do not overload the machine capacity by tilling too

deep in a single pass or at too fast a rate.

16 Never operate the tiller at high transport speeds on

hard or slippery surfaces.

17 Be careful when tilling in hard ground. The tines may

catch in the ground and propel the tiller forward. If

this occurs, let go of the handlebars and do not re-

strain the machine.

18 Use caution when tilling near fences, buildings and

underground utilities. Rotating tines can cause prop-

erty damage or personal injury.

19 Exercise extreme caution when operating on or

crossing gravel drives, walks, or roads. Stay alert for

hidden hazards or trafc. Do not carry passengers.

20 Never leave the operating position when the engine

is running.

21 Always stop the engine when tilling is delayed or

when walking from one tilling location to another.

22 Keep unit clean of vegetation and other materials.

They may become lodged between the tines. Stop

the engine and disconnect the spark plug before un-

clogging the tines.

6. Technical data

Engine: Honda 4-stroke, 196 ccm

Engine rating: 6.5 hp

Engine working speed: 3600 min-1

Working width: 330/500/800mm

Blades diameter Ø: 350 mm

Starting system: Reversing starter

Fuel: Unloaded petrol min. 91oc-

tane max. 10% bio-ethanol

Engine oil: 0.6l (15W40)

Tank capacity: 3.1 l

Weight: 81 kg

Spark plug: NGK BPR6ES

Speed

Forwards:

1. Forward gear 4.70 km/h

2. Forward gear 6.50 km/h

Backwards

Reverse gear 3.50 km/h

7. Assembly

At rst check all parts of the device and place them in

front of you on the oor.

Assembling the Support wheel (12) (Fig.3)

Attach the support wheel (12) to the frame as shown in

gure 3. For this purpose, the two holes (3a + 3b) must

be brought into conformity.

To lock the support wheel in the transport position

(Fig.32):

1. Two holes (3a + 3b) must be brought into conformity,

2. Insert pin (3d) and securing it with cotter

3. Insert pin (3e) and securing it with locking screw (3f)

and the cotter (Fig.3).

After installation, the wheel must look as shown in Fig.3.

To lock the support wheel in the working position

(Fig.33+34):

1. Loosen the support wheel from the holes (3a) and re -

block it in the holes (3c).

After installation, the wheel must look as shown in

Fig.33+34.

Fitting the Blades (Fig.3-5)

Tillage width 800 mm:

The toolholder (3g) has a hexagonal cross-section to en-

able quick installation of the blades (14).

1) Grease the toolholder (3g) and observe the alignment

of the mounting hole (3h) when installing the blades

(14) (Fig.3).

2) Insert the pin (B6, Fig.4) into the opening and secure it

with the cotter.

3) Attach the Milling broadening (15) to the petrol pow-

er cultivator and check the perfect alignment of the

mounting hole (4a).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach MTP860H Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info