Bedienungsanleitung Scheppach MTP860H (Seite 28 von 64) (Deutsch, Englisch, Französisch, Polnisch)

781993

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

28 GB

• Insert the jackleg (19) into the opening (26c) at

the pick-up point (G) (Fig.26) and secure it with

the fastening pin and the split pin (B6) (Fig. 27).

The depth of the jackleg can be adjusted in various

positions.

Plow function (Fig. 8/29/32)

Fasten the wheel mountings (I) as shown in g. 28.

• Grease the tool shaft (3g) and pay attention to the

alignment of the mounting hole (3i) (Fig. 3) when in-

stalling the wheels (K).

1) Insert the fastening pins large (B6) into the openings

and secure them with the split pins.

2) Attach the plow (J) to the desired height using a fasten-

ing pin and split pin (B6) as shown in g. 32.

Adding engine oil

Check the engine oil lever.

Failure to ll engine sump with oil before starting engine

will result in permanent damage and void engine warran-

ty (see Engine operator´s manual ).

Adding transmission oil

Check the transmission oil level.

The gearbox can be permanently damaged and the gear-

box warranty will be extinguished if the gearbox is not

lled with oil before starting (see chapter “Maintenance

& cleaning”).

Refueling

m WARNING! Always wear protective gloves when per-

forming maintenance.

This product is powered by a 4 stroke engine.

Store unleaded gasoline in a clean container approved

for gasoline.

Recommended fuel:

This engine is certied to operate on unleaded gasoline

intended for automotive use with an octane rating of 91

or higher.

Never use stale or contaminated gasoline or an oil/gas-

oline mixture. Avoid getting dirt or water in the fuel tank.

m WARNING! Follow safety instruction for fuel handling.

Always shut off engine before fuelling. Never add fuel to

a machine with a running or hot engine. Move at least 3

m from refuelling site before starting engine. DO NOT

SMOKE!

1. Clean surface around fuel cap to prevent contamina-

tion.

2. Loosen fuel cap slowly.

3. Carefully pour fuel into the tank. Avoid spillage.

4. Prior to replacing the fuel cap, clean and inspect the

gasket.

5. Immediately replace fuel cap and hand tighten.

Wipe up any fuel spillage.

m WARNING! Check for fuel leaks, if any are found, cor-

rect before use. Contact a Servicing Dealer if necessary.

8. Function

Clutch lever (3)

The forward movement of the blades is carried out by pulling

the lever upwards. The machine is stopped by releasing it.

Throttle trigger (2)

It controls the motor speed. Pulling the throttle lever in the

directions shown makes the engine run faster or slower.

Jackleg / Working depth regulator (19)

It´s for setup of the working depth. The jackleg supports

the operator in the direction and speed regulation of the

ground hook.

By lowering the depth setting the ground hook would be

braked and the working depth would be increased. By lift-

up the depth setting, the speed is faster and the working

depth would be reduced.

9. Operation

9.1 Adding fuel

Fill the fuel tank as instructed in the separate engine

manual.

9.2 Check-up before starting work

Adjusting the clutch (Fig.1)

m CAUTION! THE POWER CULTIVATOR MUST NOT

ROTATE AT IDLE SPEED.

Serious injuries may occur when the cutting tool ro-

tates at idle speed.

m ATTENTION! Make adjustments on the clutch only by

authorized personnel!

Loosen the lock screw (1b).

To adjust the clutch, turn the adjusting screw screw (1a)

in the appropriate direction:

• Counterclockwise to increase the tension of the clutch

cable,

• Clockwise to reduce the tension of the clutch cable.

The tension of the clutch cable is sufcient as soon

as the clutch lever (3) engages into the locking clutch

lever (4) when released.

m ATTENTION! Do not over-tighten the clutch!

After adjustment, tighten the lock screw (1b).

Damage to the clutch can cause the blades to rotate at

idle speed. This increases the risk of injury due to loss of

controllability and contact with the cutting tool.

9.3 Start the engine

m ATTENTION! When starting the engine, never pull the

clutch lever (3). Pulling the clutch lever (3) will accelerate

the engine, thereby rotating the machine’s milling tools

with the risk of accidents or injuries. Never wrap the start-

er cord around your hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach MTP860H Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info