Bedienungsanleitung Scheppach MTP860H (Seite 27 von 64) (Deutsch, Englisch, Französisch, Polnisch)

781993

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

27GB

4) Insert the pin (B6, Fig.4) into the opening (4a) and se-

cure it with the cotter.

5) Attach the milling protection disc (16) to the milling

broadening (15) and check the perfect alignment of the

mounting holes (5a).

6) Secure the milling protection disc (16) with the fasten-

ing pin large (B6). Then secure the pin with the cotter

against loosening.

ATTENTION! If the pin is tted incorrectly, it may be-

come detached and impair operation of the machine

with resulting damage to the machine and operator

safety risks!

ATTENTION – When tting the blades ensure blades

cutting edge is always facing into the direction of

travel.

The machine can be set to a narrower tillage width

(50 cm):

1) Remove the fastening pin large (B6) and disassem-

ble the milling protection disc (16) from the milling

broadening (15).

2) Remove the fastening pin large (B6) and disassem-

ble the milling broadening (15) from the blades (14).

3) Attach the milling protection disk (16) to the blades

(14) and check the perfect alignment of the two

mounting holes.

4) Secure the milling protection disk (16) with the fas-

tening pin large (B6). Then secure the pin with the

cotter against loosening.

Mounting Front Hand grip (H) (Fig.6)

Remove the hexagonal screws (6a) from the frame by

turning counterclockwise.

Attach the front hand grip (H) with the previously disas-

sembled hexagon head screws (6a) as shown in gure 6.

Fitting the steering column (E) (Fig. 7-12)

To install the steering column (E) proceed as follows:

• Loosen the 4 screws (7a) (Fig. 7).

• Loosen screw (8a) and remove them (Fig. 8).

Attention! Insert the pin (9a) of the steering column (E)

into the gear selector lever (22) (see Fig.9).

• The hole of the gear selector lever (22) and the hole of the

steering column pin (9a) must be brought into conformity

and the gear selector lever must be locked by using the

fastening pin small (B7) and the split pin (see Fig.9).

• Fit the cover (10a) of the gear selector lever with screw

(10b) (Fig.10).

• Mount the steering column (E) and x it with the 4

screws (11a) (see Fig. 11).

• Loosen and remove the hexagonal screw (12a) by turn-

ing it counterclockwise. Hold the support wheel (12b)

at the same time (Fig. 12).

• Pull the support wheel (12b) from the shaft (12c) (Fig. 12).

• Subsequently the lower hole at the gear selector le-

ver (22) must be brought into conformity with the hole

at the pin (12d) and locked by using the fastening pin

(12e) and the split pin (12f) as shown in Fig. 12.

• Insert the support wheel (12b) onto the shaft (12c) (Fig. 12).

Observe the correct course of the drive belts!

• Secure the support wheel (12b) with the hexagonal

screw (12a) by turning it clockwise. Hold the support

wheel (12b) at the same time (Fig. 12).

Assembling the handlebar (6) (Fig. 13-15)

Position the handlebar (6) in the seat of steering column

(7) as shown in gure 13. The height of the handlebar (6)

can be adjusted to three alternative settings.

13a - High

13b - Middle

13c - Low

Lock the handlebar with the special screw (13d) and

bracket (13e) if the required height is set.

ATTENTION!

Make sure you insert the hooked end of bracket (13e)

in hole of the handlebar (6).

Fasten the cover of the handlebar xing (D) by using the

self-tapping philips screws (B10) and the screw (B9) (see

Figs. 14 + 15).

Mounting of the throttle trigger (2) (Fig. 16-20)

Mount the throttle trigger (2) to the handlebar (6) using

screw (16a) and nut (Fig.16).

Remove the wing screw (20a) by loosening it coun-

ter-clockwise (Fig. 20).

Remove the air lter cover (8) by lifting.

Remove the wing screw (19a) by loosening it coun-

ter-clockwise (Fig.19).

Remove the air lter (19b by lifting.

Fix all control cables as shown in gure 16.

Insert the end of the throttle lever cable into the opening

at the lever (17a) (Fig.17).

Fit the throttle lever cable with the clamp (18a) as shown

in gure 18.

Install air lter (19b) and cover air lter (8) in reverse order.

Mounting of the Milling protection housing (17) (Fig.

21-23)

• Fix the rubber rings (B5) accordingly g. 21

• Attach the milling protection housing (17) with the ap-

propriate screws, washers and nuts (B12) (see Fig. 22).

• Attach the cross connector (F) with the appropriate

screws, washers and nuts (B11) (see Fig. 23).

Installing the belt cover (C) (Fig. 24)

• Fix the belt cover (C) with the wing screws (B8) as

shown in g. 24.

m ATTENTION! The protective housing must be in-

stalled!

Jackleg / Working depth regulator (19)

• Attach the pick-up point for the jackleg (G) with pin

(25a) and split pin (25b) as shown in g. 25.

• Adjust the desired side position of the jackleg with the

adjusting screws 26A and 26B.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach MTP860H Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info