Bedienungsanleitung Scheppach WDS 999 Kraft Werkzeuge (Seite 22 von 36) (Deutsch, Englisch, Französisch)

781891

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

22 І 36

10.2. Maintenance

Check the power tool and accessory parts (e.g. inser-

tion tools) for wear and damage before and after each

operation. lf necessary, replace worn out or damaged

parts with new parts and make sure to comply with

the operating instructions. Observe any technical re-

quirements.

10.2.1. Grinding plate, brushed edge

Have a qualied specialist replace damaged or worn

out grinding plates (1) and brush edges (A) with new

ones of the same type.

10.2.2. Replacing the power supply line

lf the power supply line of this power tool is damaged,

it must be replaced by the manufacturer or the cus-

tomer service or an equally qualied person in order

to avoid risks.

m WARNING! There are no parts inside the power

tool which can be serviced by the operator!

Never open the power tool! Take it to a qualied

specialist for further maintenance!

10.3. Storage

m IMPORTANT! Pull out the mains plug!

1. Whenever you do not use the power tool, you

must keep it in a dry and well ventilated place out

of the reach of children, e.g. on a high cabinet or

in a closed place.

2. Keep power tool, instruction manual and acces-

sory parts, if any, together in the original pack-

aging, if possible. Thus you have all information

and parts available at any time.

11. Transport

m IMPORTANT! Pull out the mains plug!

1. Always hold the power tool by its handle.

2. To avoid transport damages, you must pack the

power tool or use the original packaging.

3. Protect the power tool against vibrations and

shock, especially during transport in vehicles.

12. Disposal and recycling

The equipment is supplied in packaging to prevent

it from being damaged in transit. The raw materials

in this packaging can be reused or recycled. Ne-

ver place batteries in your household refuse, in re

or in water. Batteries should be collected, recycled

or disposed of by environment-friendly means. The

equipment and its accessories are made of various

types of material, such as metal and plastic. Defecti-

ve components must be disposed of as special was-

te. Ask your dealer or your local council.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with

the applicable VDE and DIN provisions. Only use

connection cables with the marking „H05VV-F“.

The printing of the type designation on the connec-

tion cable is mandatory.

AC motor

• The mains voltage must be 220 - 240 V~ 50 Hz.

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm2.

Connections and repairs of electrical equipment may

only be carried out by an electrician.

Please provide the following information in the event

of any enquiries:

• Type of current for the motor

• Machine data - type plate

10. Cleaning, maintenance, and

storage

m IMPORTANT!

Pull out the power plug before doing any cleaning and

maintenance work on the equipment. Risk of injury

from electric shock!

m IMPORTANT!

Wait until the equipment has cooled down complete-

ly! Risk of burns!

10.1. Cleaning

• Keep the equipment free of dirt and dust as far as

possible. Wipe the equipment with a clean cloth or

blow it down with compressed air at low pressure.

• We recommend that you clean the equipment im-

mediately after you use it.

• Clean the equipment regularly with a damp cloth

and some soft soap. Do not use cleaning agents

or solvents; these may be aggressive to the plastic

parts in the equipment. Ensure that no water can

get into the interior of the equipment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach WDS 999 Kraft Werkzeuge Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info