Bedienungsanleitung Snooper S6-R Neo (Seite 13 von 20) (Englisch)

619691

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Replacing the Fuse

If the detector stops operating, the fuse in the cigarette lighter plug might

be blown. If it has blown, follow these steps to replace it with a 2 amp, 5 x

20mm, fast acting fuse.

Caution: Using a fuse that does not meet these ratings or defeating fuse

protection can damage your detector, the power cable, or the vehicles

electrical system.

1. Grasp the ring near the tip of the cigarette lighter plug, then carefully

unscrew the ring by turning it counterclock-wise.

Caution: If you must use pliers to loosen the ring, be careful not to crush

the tip. Never use pliers or other tools to retighten the ring on the

cigarette lighter plug.

2. Pull the ring straight out, then remove the metal tip, spring and old

fuse.

3. Check the fuse to see if it has blown. If it has, replace it.

4. Replace the metal tip and spring inside the ring, then place the fuse

inside the cigarette lighter plug and screw the ring back onto the

plug. Make sure the metal tip is visible when you reassemble the

cigarette lighter plug.

2. Direct connecting/hard wiring your S6 NEO.

You can power your Snooper S6 by wiring it directly to your vehicles 12v

electrical system using the ’Hard Wire’ cable supplied as standard with

your unit. Firstly connect the positive side of the cable (Red) to a 12v

switched ignition live. This is a live that is On when the ignition is On and

Off when the ignition is Off. The negative side of the lead should be

connected to a negative ground, so can be attached to any metal portion

of the vehicles frame. Next plug the small adaptor on the other end of the

lead into the DC 12v input socket on the side of the unit.

Important: If you are unfamiliar with this procedure, please consult a

professional auto electrician

have made your choice press the ’Select’ button. The screen will read

’SETTING CONFIRMED’ to confirm your selection and will return to the

Menu screen.

Note: To return to the Menu screen from the Sub Menu screen, press

the button below ’Back’ (2) on the display. To return to the Standby

screen from the Menu screen press the same button, which will now say

Cancel . If no buttons are pressed on the device for a period of five

seconds the screen will automatically return to the Standby display.

8. Atomic Clock

This is a selectable feature that allows you to have the time shown on the

display of your S6 provided by the GPS Atomic Clock. The time on this

clock is generated directly from GMT and is completely accurate. The S6

comes with this feature turned on as the factory default setting.

To activate or de-activate the Atomic Clock follow these instructions.

From the Standby screen press the button below ’Menu’ on the LCD

display and then using the buttons below the Up and Down arrows, scroll

the display until ’ATOMIC CLOCK’ is highlighted and press ’Select’. Using

the buttons below the arrows on the display, highlight your desired

setting, either ’ON’ or ’OFF’. Once you have made your choice press the

’Select’ button. If you select ’ON’ the device will give you the option to

select British Summer Time (BST) or Greenwich Mean Time (GMT).

Using buttons 3 or 4 choose your

desired setting and press ’Select’.

The screen will read ’SETTING

CONFIRMED’ to confirm your

selection and will return to the

Menu screen.

Note: To return to the Menu screen

from the Sub Menu screen, press

the button below ’Back’ (2) on the

display. To return to the Standby

screen from the Menu screen press the same button, which will now say

Cancel . If no buttons are pressed on the device for a period of five

seconds the screen will automatically return to the Standby display.

9. Setting the LCD backlight alert

The LCD display on the Snooper S6 has a backlight so that at night or in

dark conditions you will still be able to clearly read the information on the

display. The backlight has three settings that you can choose from. The

S6 can be programmed so that the backlight is permanently ON (This is

the default factory setting) or permanently OFF when the unit is powered

up or you can programme the Backlight to come on only during an alert.

2 3 4 5

BST

GMT

BACK

SELECT

SUB MENU

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snooper S6-R Neo Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info