Bedienungsanleitung Snooper S6-R Neo (Seite 18 von 20) (Englisch)

619691

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Operating Instructions

1. Starting Up

After you have successfully installed your S6 or S6-R and performed the

download it is time to perform the first start up. Firstly make sure your

vehicle is parked in as open a space as possible, clear of tall trees and

buildings so that the GPS extension antenna has a clear view of the sky

above. Next power the unit up by pressing Button 1 (please refer to

diagram on page 4). The LCD display will briefly read ’Snooper’ and will

then automatically change to the ’SEARCHING’ display. The S6 needs to

acquire a minimum of 3 satellites to work effectively. Once this has been

achieved the S6 will proceed to the standby screen (See Standby Screen

next in this section) and the satellite counter on the left hand side of the

display will indicate how many satellites your unit can currently see. As

soon as the standby screen is displayed your S6 is ready for use and will

now automatically alert you of any locations stored in its database (as

well as radar and laser alerts if you have the S6-RLD connected). A

variety of Audible and Visual alert patterns are explained later on in this

section. See ’Features and Settings’ to personalise your unit.

As the GPS engine and antenna have never been used before, the first

’Cold’ start up could take as long as thirty minutes. Once initialised,

subsequent start-ups will take as little as three minutes.

2. Standby Screen

The Standby Screen is the screen you will see when your unit is powered

up and successfully installed. It is the display you will see when the unit is

not currently detecting or locating a source of radar, laser or a stored

coordinate.

SPEED

30MPH

CITY CANCEL MUTE MENU

Note: To return to the Menu screen from the Sub Menu screen, press

the button below ’Back’ (2) on the display. To return to the Standby

screen from the Menu screen press the same button, which will now say

Cancel . If no buttons are pressed on the device for a period of five

seconds the screen will automatically return to the Standby display.

SET PRE-ALERT - After selecting

’SET PRE ALERT’ in the ALERT

SETTINGS Sub Menu , the display

will read ’DISTANCE’ with either the

factory default warning distance or

your previous selection displayed.

To increase the distance that your

S6 detects from press the button

below the Up arrow (3) until the

distance you require is shown on the

display. To decrease the distance that your S6 detects from, press the

Down button (4) until the distance you require is shown on the display.

Once you have made your selection press the ’Select’ button (5). The

display will read ’SETTING CONFIRMED’ to confirm your selection and

will return to the Menu screen.

Note: To return to the Menu screen from the Sub Menu screen, press

the button below ’Back’ (2) on the display. To return to the Standby

screen from the Menu screen press the same button, which will now say

Cancel . If no buttons are pressed on the device for a period of five

seconds the screen will automatically return to the Standby display.

2. Radar/Laser detector settings - S6-RLD only.

This setting is only applicable if you have purchased the S6-R, or the S6-

RLD as an optional extra, and allows you to turn the RLD off in low risk

situations and choose between receiving both Radar and Laser alerts or

Laser only.

From the Standby screen press the

button below ’Menu’ on the LCD

display and then using the buttons

below the Up (3) and Down (4)

arrows on the LCD display, scroll

until ’RADAR & LASER’ is highlighted.

Then simply press the button below

’Select’ (5) on the display and again

using the buttons below the arrows

on the display, highlight your desired

setting, choosing either ’RADAR &

LASER’, ’LASER ONLY’ or ’OFF’.

Once you have made your choice

press the ’Select’ button. The screen

will read ’SETTING CONFIRMED’ to

confirm your selection and will return

to the Menu screen.

SUB-MENU

Back

Select

DISTANCE : 500M

2 3 4 5

1. ALERT SETTING

2. RADAR & LASER

3. AUTOMUTE

RADAR & LASER

LASER ONLY

OFF

BACK

SELECT

CANCEL

SELECT

BACK

SELECT

09.30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snooper S6-R Neo Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info