Bedienungsanleitung Snooper S6-R Neo (Seite 17 von 20) (Englisch)

619691

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- Next use a damp cloth to thoroughly clean the bottom of the S6-RLD

and the side of the bracket where you intend to mount the device.

- Peel the backing paper from one side of the water resistant double-

sided tape and apply it to the bottom of the unit.

- Next remove the backing paper from the

other side of the tape and position the

S6-RLD onto the ’L’ shaped bracket as

indicated in the diagram below ensuring

that the front of the detector is facing

forwards down the road. Please note it will

take approximately 24hrs for the water

resistant double-sided tape to adhere properly

to the bracket and unit.

- Feed the cable from the S6-RLD through an

existing grommet in the bulkhead to the

cockpit of the vehicle and plug the end of

the cable into the socket on the side of the

S6 GPS control panel marked ’RD’.

If there is not a convenient grommet

to use you will need to drill an

additional hole sealed with a

grommet, large enough to feed the

cable and plug through. Ensure

that the cable running from the

S6-RLD to the GPS control

panel is secured periodically

so that it does not interfere with any

of the workings of the vehicle.

- The S6 control panel indicates that you have

successfully installed the RLD by showing an ’RD’ icon on the start-up

screen when the unit is powered up. Note: The RD icon is not

displayed on the Standby screen.

Mounting Notes

When mounting the S6-RLD always ensure that you mount the unit away

from any moving parts such as air-cooling fans or the fan belt. Always

position the unit so that you can safely feed the cable back through to the

cockpit of the vehicle without the cable interfering with any moving parts

within the engine bay or interfering with any part of the vehicle that could

endanger you or your passengers. Please check that all surfaces are

safe to drill through before beginning any work.

Important: If you are unfamiliar with any of the above

procedures, please consult a professional auto electrician.

Note: To return to the Menu screen from the Sub Menu screen, press

the button below ’Back’ (2) on the display. To return to the Standby

screen from the Menu screen press the same button, which will now say

Cancel . If no buttons are pressed on the device for a period of five

seconds the screen will automatically return to the Standby display.

3. Automute

The Automute setting offers the user an alternative audible alert. If

Automute is selected, when your device detects a signal, rather than

continually beeping through the alert, it simply beeps a small number of

times, depending on the strength of the signal and will then only emit a

low volume beeping sound until you are out of range of the source. This

allows you to receive a normal audible alert followed by a quieter audible

alert instead of a continuous one. To select or de-select the Automute

please refer to the following instructions.

From the Standby screen press the

button below ’Menu’ on the LCD

display. Using the buttons below the

Up (3) and Down (4) arrows, scroll

the display until ’AUTOMUTE’ is

highlighted on the screen and press

the button below ’Select’ (5) on the

display. Then using the buttons below

the arrows on the display, highlight your

desired setting, either ’ON’ or ’OFF’. Once

you have made your choice press the ’Select’ button. The screen will

read ’SETTING CONFIRMED’ to confirm your selection and will return to

the Menu screen.

Note: To return to the Menu screen from the Sub Menu screen, press

the button below ’Back’ (2) on the display. To return to the Standby

screen from the Menu screen press the same button, which will now say

Cancel . If no buttons are pressed on the device for a period of five

seconds the screen will automatically return to the Standby display.

4. Speed Limit Alert

This safety feature has been designed to let you programme your S6 to

alert you when you reach any speed you choose. For instance you could

set your S6 to alert you when your speed reaches 30mph so that you

never accidentally stray over the speed

limit. To set the Speed Limit Alert

please refer to the following instructions.

From the Standby screen press the

button below ’Menu’ on the LCD

display and then using the buttons

below the Up (3) and Down (4) arrows

on the LCD display, scroll until the

screen reads ’SET SPEED LIMIT’

2 3 4 5

OFF

SUB MENU

3 4 5

3. AUTOMUTE

4. SET SPEED LIMIT

BACK

SELECT

CANCEL

SELECT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snooper S6-R Neo Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info