Bedienungsanleitung Snooper S6-R Neo (Seite 14 von 20) (Englisch)

619691

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Installation S6-RLD

If you have purchased the S6-R or have purchased the S6-RLD as an

optional extra to your S6 you will need to refer to the following

instructions to install the S6 remote extension radar and laser detector.

This device is waterproof so can be installed under the bonnet behind the

vehicles grille or within an air intake at the front of your car or you can

simply mount the device on the dashboard or windscreen of your vehicle.

Please note however that some vehicles including Renault, Citroen and

Peugeot may come with a ’Heat Reflective’ or ’Comfort’ front windscreen,

which may affect the performance of the S6-RLD. In these cases the RLD

must be mounted outside the vehicle. For this type of installation follow

the instructions for S6-RLD External Installation.

1. Dashboard Mounting

The S6 RLD needs a clear view of the road ahead and needs to be

positioned in as horizontal a position as possible. If you can find a

position on the dashboard that is fairly flat (surface must be within 15-20

degrees of the road) and so that the view from the front of the detector is

through clear glass and is not obscured by any metallic objects such as

the windscreen wipers, the Hook and Loop fastener might provide the

easiest method of mounting the detector. To mount the RLD in this way

follow these instructions.

- Use a damp cloth to thoroughly clean

the bottom of the S6-RLD and the area

where you intend to mount the device.

- With the two parts of the Hook and

Loop fastener still fastened together,

peel the backing tape from the softer

’Loop’ side of the fastener and

apply it to the bottom of the unit.

- Next remove the backing tape

from the ’Hook’ side of the

fastener, again whilst the

two parts are still fastened

and position the unit onto the

desired area. Please note it

will take approximately 24hrs for

the Hook and Loop fastener to

adhere properly to the dashboard

and unit.

- Finally feed the cable from the S6-RLD to

the S6 GPS control panel, concealing it as

well as possible and plug it into the socket

marked ’RD’ on the side of the control panel.

To change the Logic Mode setting follow these instructions.

From the Standby screen press the button below ’Menu’ on the LCD

display and then using the buttons below the Up (3) and Down (4)

arrows, scroll the display until

’SAFETY CAMERAS’ is highlighted

and press ’Select’ (5). Then using the

buttons below the arrows on the

display, highlight the features you

would like to set, either ’SET LOGIC

MODE’ or ’SET SMART MUTE ’and

press ’Select’. Next highlight your

preferred Logic Mode by again using

the up or down arrows. Once you have

made your choice press the ’Select’

button. The screen will read ’SETTING

CONFIRMED’ to confirm your selection

and will return to the Menu screen.

Note: To return to the Menu screen

from the Sub Menu screen, press

the button below ’Back’ (2) on the

display. To return to the Standby

screen from the Menu screen press

the same button, which will now say

Cancel . If no buttons are pressed on the device for a period of five

seconds the screen will automatically return to the Standby display.

Smart Mute - The Smart Mute setting has been designed so that you

only receive a visual alert generated by the S6 GPS control panel if you

are travelling below the posted speed limit as you approach a given

location such as a Gatso camera. If you are travelling above the posted

speed limit you will receive both a visual and an audible alert as normal.

The Smart Mute setting also activates a radar/laser filter designed to filter

out any radar/laser signals you should encounter whilst travelling below

20mph.

To activate the Smart Mute setting follow these instructions.

From the Standby screen press the

button below ’Menu’ on the LCD

display and using the buttons below

the Up (3) and Down (4) arrows on

the screen, scroll the display until

’SAFETY CAMERAS’ is highlighted

and press ’Select’ (5). Then using the

buttons below the arrows on the

display, highlight ’SET SMART MUTE’

and press ’Select’. Use the up or down

arrows to highlight your desired setting, either ’ON’ or ’OFF’. Once you

2 3 4 5

SET LOGIC MODE

SET SMART MUTE

LOGIC MODE 1

LOGIC MODE 2

LOGIC MODE 3

2 3 4 5

OFF

BACK

SELECT

SUB MENU

BACK

SELECT

SUB MENU

BACK

SELECT

SUB MENU

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snooper S6-R Neo Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info