Bedienungsanleitung Spektrum DX8 (Seite 13 von 42) (Englisch)

708059

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite





The Range Test function reduces the power output. This allows for a range

test to conﬁrm the RF link is operating correctly. Perform a range check at the

beginning of each ﬂying session to conﬁrm system operation.



With the transmitter on and the main or telemetry screen displayed, press the

roller. The Function list displays.

Rotate the roller to highlight Range Test then press the roller to access the Range

Test function.

With the Range Test screen displayed, push and hold the trainer button. The

screen displays Reduced Power. In this mode the RF output is reduced allowing

for an operational range test of your system.

If you let go of the trainer button, the transmitter will go back to Full Power.

Range Testing the DX8

1. With the model restrained on the ground, stand 30 paces

(approx. 90 feet/28 meters) away from the model.

2. Face the model with the transmitter in your normal ﬂying position and place

the transmitter into Range Test mode (see above) and push the trainer button

reducing the power output.

3. Operate the controls. You should have total control of your model with the

transmitter in Range Test mode.

4. If control issues occur contact the appropriate Horizon Product Support

ofﬁce for assistance.

5. If performing a range test while a telemetry module is active, the display will

show ﬂight log data.



The DX8 organizes the programming screens in two separate categories:

System Setup Mode and Functions Mode. The System Setup Mode contains

programming that is generally used when initially setting up a model, and

seldom used at the ﬁeld. System Setup functions includes Model Type, Model

Name, Wing Type, (Swashplate Type for Helis) Model Reset, etc. Note: No

radio transmission occurs when a System Setup screen is displayed to prevent

accidental servo operation. This protects linkages/servo gears from damage when

making programming changes. System Setup in Airplane and Heli Model type

includes the following screens.

 

Model Select page 14 Model Select page 14

Model Type page 14 Model Type page 14

Model Name page 15 Model Name page 15

Wing Type page 15 Swash Type page 15

Switch Select page 15 Switch Select page 16

Trim Step page 16 F-Mode Setup page 16

Model Reset page 17 Trim Step page 16

Model Copy page 17 Model Reset page 17

Warnings page 18 Model Copy page 17

Telemetry page 18 Warnings page 18

Frame Rate page 20 Telemetry page 18

Trainer page 20 Frame Rate page 20

System Settings page 20 Trainer page 20

Transfer SD Card page 21 System Settings page 20

Transfer SD Card page 21



Press and hold the roller while turning on the transmitter. When System Setup

appears on the screen, release the roller. The DX8 is now in System Setup Mode.



In the System Setup list rotate the roller to highlight the desired function then

press the roller to access. The selected function screen will appear.

30 paces (90 feet/28 meters)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX8 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info