Bedienungsanleitung Spektrum DX8 (Seite 15 von 42) (Englisch)

708059

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite





The Model Name function allows you to name a model using up to 10 characters.

This makes identifying and selecting models much easier. Naming a model is

normally done during initial setup. You can modify or change names at any time

without affecting other programming. Typical model names include Vibe 50 3D,

Extra 300, Blade 400, Sport 40 #1, etc. Note that upper case, lower case, numbers

and symbols are available.



Press and hold the roller while turning on the transmitter. When System Setup

appears on the screen, release the roller. The DX8 is now in System Setup Mode.

Rotate the roller to highlight Model Name then press to access the function.

The following screen appears:

Rotate the roller to highlight the desired character then press to accept.

Repeat the process until complete. The name will display on the main screen.

Pressing  will erase the current character.



Use the Wing Type function to program the wing and tail mix to match your

airplane. Eight wing types (Normal, elevon, dual aileron, 1 aileron and 1 ﬂap,

ﬂaperon, 1 aileron and 2 ﬂaps, 2 ailerons and 1 ﬂap, 2 ailerons and 2 ﬂaps) and

ﬁve tail types (normal, V-Tail, dual elevator, dual rudder, dual rudder/ elevator) are

available. You must select the correct wing and tail type to match your airplane

before doing any other wing or tail related programming (e.g., Flaps, Travel

Adjust, Sub-Trim, etc.).



Press and hold the roller while turning on the transmitter. When System Setup

appears on the screen, release the roller. The DX8 is now in System Setup Mode.

Rotate the roller to highlight Wing Type then press to access the function.

The following screen appears:

Rotate the roller to highlight Wing and press to access the function. Rotate the

roller to the desired wing mix. Press the roller to select.



Rotate the roller to highlight Tail then press.

Rotate the roller to access the desired tail type. Press the roller to select.



The Switch Select function allows the switches, knob and right and left trimmers

to be assigned to the gear, Aux1, Aux2 or Aux3 channels or inhibit.



Press and hold the roller while turning on the transmitter. When System Setup

appears on the screen, release the roller. The DX8 is now in System Setup Mode.

Rotate the roller to highlight the desired switch, knob or trimmer then press the

roller to access.

Rotate the roller to select the desired channel or function you wish the switch,

knob or trimmer to operate. Press the roller to accept. Note that the channel or

function can only be assigned once.

Repeat to select all desired switch positions.



Use the Swash Type screen to program the swashplate mix to match your

helicopter swashplate type. Six swashplate types are available: Normal, 3-servo

120 CCPM, 3-servo 140 CCPM, 3-servo 90 CCPM, 3-servo 135 CCPM, and

2-servo 180 CCPM. Select the correct swashplate type to match the speciﬁc

helicopter before doing any other cyclic programming e.g., Pitch Curve, Travel

Adjust, Sub-Trim, etc.). If in doubt consult your helicopter’s manual for correct

swashplate mixing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX8 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info