Bedienungsanleitung Spektrum DX8 (Seite 24 von 42) (Englisch)

708059

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite





Rotate the roller to highlight Sw (switch) then press to access the switch options.

Select the desired switch to change the dual rate for that channel or inhibit then

press the roller to make it active.

Note: You can assign multiple channels to a single switch to affect the

dual and exponential rates of all.



Note Pos: Pos 0 in the center of the screen. Move the switch displayed at the

bottom of the screen to one of three positions from 0,1,2. When you make D/R or

Expo adjustments, values are assigned and automatically active when the switch

is in that position (Pos 0, 1or 2).



Conﬁrm that the desired channel and switch position are selected. Rotate

the roller to highlight the D/R or Expo value then press to access. When the

corresponding channel’s control stick is centered both values are highlighted. If

you move the control stick to its endpoint, only one value will be highlighted.

This allows the D/R or Expo value in that direction only to change. With the

desired value selected, rotate the roller to select.



The Differential function provides precise adjustments of up/down aileron travel

of each aileron (or elevon if Delta wing is activated). Typically, you can use

Aileron differential to reduce unwanted yaw characteristics. In aerobatic airplanes

adjusting differential provides an axial roll (minimum displacement of yaw

during a roll). You can program up to three Differential values and assign them

to a switch. Note that positive + and negative – differential is available; however,

normally more up aileron travel is required than down aileron.

Note: The Differential function is only available if Dual Aileron, Flaperon,

2 ailerons 1 flap, 2 ailerons 2 flaps or Elevon is selected in Wing Type

(see page 13) and each aileron servo is controlled by its own channel.



With the transmitter on and the main or telemetry screen displayed, press the

roller. The Function list displays.

Rotate the roller to highlight Differential then press.

Differential defaults to Inhibit. Press the roller to highlight Inhibit then select one

of the following switch positions:

- Off

 - Always on

- Gear Switch

 - Flap switch

 - Aileron Dual rate switch

Ele D/R - Elevator Dual rate switch

Rud D/R - Rudder dual rate switch

 - Flight Mode switch

 - Aux 2 switch

 - Mix switch

Press the roller to accept the desired switch. The differential adjustment screen

displays.

Highlight the desired differential position/value and press the roller to access.

Rotate the roller to change the value then press the roller. Repeat for all switch

positions desired.

Positive differential values provide more up than down aileron travel. Negative

differential values provide more down than up travel. The differential values

screen also allows you to select/change switch positions. Use the roller to

highlight SW then rotate to change to the desired switch position or inhibit the

function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX8 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info