Bedienungsanleitung Visonic Powermaster-360 (Seite 22 von 96) (Englisch)

769323

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

22 D-307500 PowerMaster 360 Installer's Guide

Part B - Configuration

Step 1



Step 2



Step 3



Step 4



Enter Location Menu

[1]

Select Location

(see list below)

[2]

Enter Zone Type

[3]

Select Zone Type

(see list below)

[4]

➯



➯



Z10:LOCATION

Dining room 



Custom 5

Z10:ZONE TYPE

1:Exit/Entry1 



5. Interior

Step 5



Step 6



Step 7



Step 8



Enter Chime Menu

[5]

Select Chime option

[6]

Enter Partitions Menu

[7]

Select Partition options

[8]

➯



➯



Z10:SET CHIME

chime OFF 



melody-chime

Z10:PARTITIONS

Z10:P1 P2 P3

Step 9



Step 10



Step 11

Enter Device Settings

[9]

Configure Device

Parameters

[10]

Continue or End

➯



Z10:DEV SETTINGS

Refer to device

datasheet in the device

Installation Instructions

for specific configuration

instructions.

To continue –

See  [11]



- Configuring New Devices

Location (name) setting:

[1]

To review or change the Location (name) setting, press the button, otherwise scroll to the next option.

[2]

To change the Location name, enter the menu and select the name from the Location List below. You can

assign additional custom names using the 06.CUSTOM NAMES option in the Installer Mode menu. See section

4.7.

Note: As a shortcut, press the 2 digit serial No. of the Custom Location, which takes you directly to its menu.

Zone Type setting:

[3]

To review or change the Zone Type setting, press the button, otherwise scroll to the next option.

[4]

The zone type determines how the system handles signals sent from the device. Press and select a

suitable zone type. The list of available Zone Types and the explanation for each zone type is provided below.

Note: As a shortcut, press the 2 digit serial No. of the Zone Type shown in the Location List below, which takes

you directly to its menu.

Chime setting:

[5]

All zones are set to chime OFF by default. To configure the device to cause the panel to sound (when disarmed) a

Chime melody when tripped, press the button, otherwise scroll to the next option.

[6]

Select between Chime OFF, melody-chime, and zone name-chime. In melody chime the control panel

sounds a chime melody when the sensor is tripped. In zone name-chime the control panel sounds the zone

name when the sensor is tripped. The chime operates during the Disarm mode only.

Partitions setting:

Note: The PARTITIONS menu appears only if Partitions is enabled in the control panel (see section 4.13).

[7]

When entering the menu, the display shows the default Partition selection (marked with ).

[8]

Use the keypad keys , , to assign partitions to the device.

Device Configuration:

[9]

To review or change the Device Configuration (settings), press the button, otherwise scroll to the next

option – see  [11].

[10]

To configure the device parameters, refer to its corresponding device datasheet in the device Installation

Instructions. The defaults of the device parameters can be also configured as explained in section 4.4.7.

[11]

After completing the configuration of the device, the wizard brings you to the Next Step menu with the following

3 options:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic Powermaster-360 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info