Bedienungsanleitung Webasto Pure II (Seite 18 von 379) (Alle Sprachen)

802209

Zoom out

Zoom in

Vorherige Seite

1/379

Nächste Seite

6 5110757E OI II Webasto Pure

NOTE

In some countries, single-phase charging is limited to

a defined current. The local connection requirements

must be observed.

All protective devices specified below must be designed

such that the charging station is disconnected from the

grid in the case of a fault. You must meet national install-

ation regulations and standards when selecting the pro-

tective device.

8.2.1 Dimensioning of the Residual Current

Circuit Breaker (RCCB)

The national installation regulations generally apply. Un-

less otherwise specified therein, each charging station

must be protected by an appropriate residual current

device (RCD type A) with a trip current of ≤30mA.

8.2.2 Dimensioning of the circuit breaker

The circuit breaker must conform to IEC 60898. The let-

through energy (I²t) must not exceed a maximum 80,000

A²s.

Alternatively, a residual current circuit breaker combina-

tion (RCBO) according to EN 61009-1 can be used. The

aforementioned parameters apply for this circuit breaker

combination.

8.2.3 Mains isolation device

The charging station does not have its own main ON/OFF

switch. The protective devices installed in the power sup-

ply system are therefore also used to disconnect the

power supply.

8.3 Installation

See also chapter15, "Assembly" on page 9. The sup-

plied installation material is intended for mounting the

charging station on a concrete wall or on an external

stand. For installation on a stand, the mounting material

is included in the scope of delivery of the stand.

üScope of delivery is checked for completeness.

uTake into account the mounting position at the install-

ation location. See Fig. 14.

NOTE

The central hole must be drilled!

uRemove the drill template at the perforation from the

packaging.

uMark the four positions of the drill holes at the install-

ation location using the drill template. See Fig. 14.

uDrill 4 holes of Ø 8mm in the marked positions.

uPosition the bracket over the upper holes and mount

using 2 wall plugs and 2 screws, 6x70mm, T25.

uRemove the lower cover from the connection area of

the charging station.

Fig.8

uRemove the spiral antikink protection from the con-

nection area of the charging station and place it with

the other supplied material.

uFor surface mounting, make a recess for routing the

lead on the back of the charging station using the des-

ignated lateral predeterminedbreakingpoints (if ne-

cessary deburr the edge of the break using a round

file).

uInsert the lead through the designated lead-through

and fit the charging station on the previously mounted

bracket.

uMount the charging station using 2 screws,

6x90mm, T25 using the mounting holes in the lower

connection area. Do not exceed the max. torque of

6Nm.

8.3.1 Connecting the charging cable

uPush the spiral antikink protection with the threadless

opening forward over the supplied charging cable.

uGuide the charging cables through the previously pre-

assembled sealing clip.

NOTE

Ensure correct fit of the previously pre-assembled rub-

ber seals in the sealing clip.

uPush the charging cable at least 10mm beyond the

upper edge of the clamping area of the strain relief

clamp.

uTurn the antikink protection spiral several turns onto

the sealing clip.

NOTE

Do not tighten yet.

Fig.9

uScrew in the supplied strain relief clamp in the correct

position on the charging cable.

NOTE

The strain relief clamp has two position options for

charging cable versions 11kW and 22kW.

Ensure that the “11 kW installed” label for an 11 kW

charging cable is visible.

uFit the strain relief clamp in the correct mounting posi-

tion using the supplied self-tapping Torx screws

(6.5x25mm) and tighten to 5.5Nm. (Attention: Do

not overtighten screws).

uThe strain relief clamp must be flush when securely

screwed in.

NOTE

Perform a tension test on the charging cable to make

sure that the cable cannot move.

uScrew the antikink protection spiral onto the sealing

clip with a torque of 4Nm.

uUsing the slot-head screwdriver (3.5 mm), connect the

individual cable ends according to the specification in

the illustration on the right terminal block with the

"out" label.

uTo do this, insert the screwdriver in the designated up-

per opening of the spring relief for the terminal block

and open the clamping spring.

uNow insert the individual wire into the designated

connection opening of the terminal block (lower open-

ing).

Charging cable Description

Blue N

Brown L1

Black L2

Grey L3

Yellow-green PE

Black-white Control cable (CP)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Pure II Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info