Bedienungsanleitung Yamaha MOTIF8 (Seite 237 von 300) (Englisch)

571289

237

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

237

MOTIF Reference

Sampling Record mode

Reference Sampling mode

Sampling Standby

The explanations here apply to step #6 of the Basic

Procedure on page 234.

• TriggerMode

Speciﬁes the method by which sampling will be triggered.

❏ Settings

vel

Sampling will begin as soon as an input signal exceeding

the speciﬁed trigger level is received after the [F6]

(START) button is pressed.

When this is selected, you need also set the Trigger Level

(1~127).

meas

This is available only when entering the Sampling mode

from the Song/Pattern mode and should be set together

with the Punch-in/out measure.

After the [F6] (START) button is pressed, sampling will

begin at the speciﬁed punch-in measure, and end at the

speciﬁed punch-out measure. Sampling will also stop when

the Song/Pattern is stopped by pressing the [■] button.

manual

Sampling will begin as soon as the [F6] (START) button is

pressed, regardless of the Song/Pattern playback status.

• RecMonitor (Recording Monitor)

Determines the output level of the monitor for the input

signal.

This monitor signal is output from the PHONES jack or

the OUTPUT R and L/MONO jacks. This has no effect on

the recording level.

❏ Settings 0~127

• RecGain (Recording Gain)

Determines the recording gain when resampling.

This parameter is available only when the Source is set to

“resample.”

❏ Settings -12dB~+12dB

Trigger Waiting

The following display applies to step #7 of the Basic

Procedure on page 234. The following display is

available when the Trigger mode is set to “level.” In

this case, sample recording is on standby, waiting for

an input signal that exceeds the Trigger level.

Punch-in Waiting

The following display applies to step #7 of the Basic

Procedure on page 234.

The following display is available when entering the

Sampling mode from the Song/Pattern mode and when

the Trigger mode is set to “meas.” In this case, sample

recording is on standby, waiting for song/pattern

playback to reach the speciﬁed Punch-in measure.

Slice setting after sampling

The explanations here apply to step #9 of the Basic

Procedure on page 235.

If you’ve entered the Sampling Record mode for the

Song or Pattern mode and you’ve set the sampling type

to “slice+seq,” you should set the following Slice-

related parameters.

■ [F1] Trim

The trim function makes it possible to specify the

beginning and end points to be played back within an

entire sample. You can delete all unnecessary sample

data (located ahead of the Start point and located after

the End point) by pressing the [SF5] button (Extract

function). This function is especially useful in creating

drum loops, since it helps you isolate only the beats

you need for your loop.You can also specify the tempo

for the range of the looped playback to determine its

beat.

Indicates the MOTIF is in the Sampling Standby mode.

Indicates that sample recording is waiting

for a signal of an appropriate level.

Indicates that sample recording is waiting

for a signal of an appropriate level.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF8 Seite 237

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info