Bedienungsanleitung Casio 3134 (Seite 9 von 15) (Englisch)

466632

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Operation Guide 3134 3205

Countdown Timer Examples

Countdown start time: 10 minutes; Reset time: 5 minutes

Progress beeper: On

10'00"

Start Time Reset Time

0'00"1'00" 0'10"2'00"3'00"4'00"5'00"

Reset Period

Reset Period Beeper

Countdown

End Beeper

Reset Time Beeper

0'01"0'02"0'03"0'04"0'05"0'06"0'07"0'08"0'09"0'10" 0'00"

To configure countdown timer settings

While the countdown start time is on the display

in the Countdown Timer Mode, hold down E

until the countdown start time setting starts to

flash, which indicates the setting screen.

•If the countdown start time is not displayed,

use the procedure under “To use the

countdown timer” to display it.

Press D to move the flashing in the sequence

shown below to select other settings.

Start

Time

Reset

Time

3. When the setting you want to change is flashing, use A and C to change

it as described below.

4. Press E to exit the setting screen.

•The reset time setting must be less than the countdown start time setting.

To turn the progress beeper on and off

Pressing B while the countdown start time is on the display or while a

countdown timer operation is in progress in the Countdown Timer Mode

toggles progress beeper operation on ( displayed) and off

( displayed).

Setting

Start Time

Reset Time

Screen Button Operations

Use A (+) and C (–) to change the setting.

•You can set a start time in the range of 1 to 60

minutes in 1-minute increments.

Use A (+) and C (–) to change the setting.

•You can set a reset time in the range of 1 to 5

minutes in 1-minute increments.

To use the countdown timer

In the Countdown Timer Mode, press A to start

the countdown timer.

•The countdown timer measurement operation

continues even if you exit the Countdown Timer

Mode.

•

The table below describes button operations you

can perform to control countdown operations.

Stopwatch

The stopwatch lets you measure elapsed time,

split times, and two finishes.

•The display range of the stopwatch is 23 hours,

59 minutes, 59.99 seconds.

•The stopwatch continues to run, restarting from

zero after it reaches its limit, until you stop it.

•The stopwatch measurement operation

continues even if you exit the Stopwatch Mode.

•Exiting the Stopwatch Mode while a split time is

frozen on the display clears the split time and

returns to elapsed time measurement.

•All of the operations in this section are

performed in the Stopwatch Mode, which you

enter by pressing D.

Minutes

Current time

1/100 second

Hours

Seconds

JJ J

First runner

finishes.

Display time

of first runner.

Elapsed Time

AA A A C

Start Stop Re-start Stop Clear

Split Time

AC C A C

Start Split Split release Stop Clear

Two Finishes

AC A C C

Start Split Stop Split release Clear

Display time of

second runner.

Second runner

finishes.

(SPL displayed)

To measure times with the stopwatch

World Time

World Time displays the current time in 33 cities

(29 time zones) around the world.

•If the current time shown for a city is wrong,

check your Home City time settings and make

the necessary changes.

•All of the operations in this section are

performed in the World Time Mode, which you

enter by pressing D.

To view the time in another city

In the World Time Mode, use A (east) and C

(west) to scroll through city codes (time zones).

•For full information on city codes, see the “City

Code Table”.

Timekeeping

Mode time

Current time in the zone

of the selected city code

City code

To toggle a city code time between Standard Time and Daylight

Saving Time

1. In the World Time Mode, use A (east) and C

(west) to display the city code (time zone)

whose Standard Time/Daylight Saving Time

setting you want to change.

2. Hold down E to toggle between Daylight

Saving Time (DST indicator displayed) and

Standard Time (DST indicator not displayed).

•The DST indicator appears on the display

whenever you display a city code for which

Daylight Saving Time is turned on.

•You cannot toggle between Daylight Saving Time and Standard Time if the

displayed city code is UTC.

•Note that the DST/Standard Time setting affects only the currently

displayed city code. Other city codes are not affected.

DST indicator

Countdown End Beeper

The watch beeps each second of the final 10 seconds before a countdown

reaches zero, and at zero. The first five beeps (seconds 10 through 6) are

higher pitched than the final five beeps (seconds 5 through 1). The watch

emits a longer beep to signal when the countdown reaches zero.

Progress Beeper

The progress beeper actually includes two beepers: a reset time beeper and

a reset period beeper.

•Note that the reset time beeper and reset period beeper operate only while

the progress beeper is turned on. For more information, see “To turn the

progress beeper on and off”.

Reset Time Beeper

The reset time beeper is similar to the countdown end beeper. The watch

beeps each second of the final 10 seconds before the countdown reaches the

reset time.

Reset Period Beeper

The reset period is the portion of the countdown between the reset time and

zero. While timing is in the reset period, the watch will beep four times at the

top of each minute and 10 seconds before the end of the countdown.

To do this:

Stop the countdown operation

Resume a stopped countdown operation

Display the countdown start time

Stop the countdown operation and display the reset

time

Start the countdown from the displayed reset time

Do this:

Press A.

Press A again.

While the countdown is

stopped, press C.

Press C.

Press A.

Casio 3134 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 3134

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info