Bedienungsanleitung DeWalt DCE080GS (Seite 24 von 232) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790944

Zoom out

Zoom in

Vorherige Seite

1/232

Nächste Seite

GB Accessories

Recommended accessories for use with your tool are available for

purchase at your factory-owned local service center.

WARNING:

Since accessories other than those offered by DEWALT

have not been tested with this laser, use of such

accessories with this laser could be hazardous. To reduce

the risk of injury, only use DEWALT® accessories that are

recommended for use with this rotary laser.

If you need assistance in locating any accessory, please visit our

website www.2helpU.com

Mounting Bracket

Some laser kits include a mounting bracket, which can be used for

attaching the tool to a track or to a ceiling grid to aid in acoustical

ceiling installation. Follow the directions below for using the mounting

bracket.

CAUTION:

Before attaching the laser level to wall track or ceiling

angle, be sure that the track or angle is properly

secured.

1. Place the laser on the mounting base (Figure P 5) aligning the

5/8–11 screw hole on the tripod adapter (Figure G 1), attached

to the bottom of the laser with the hole (Figure P 6) in the

mounting base.

2. Turn the mounting knob (Figure P 3) to secure the laser.

3. With the bracket's measuring scale (Figure P 7) facing you,

loosen the clamp locking knob (Figure P 8) to open the clamp

jaws.

4. Position the clamp jaws around the wall track or ceiling angle

and tighten the clamp locking knob (Figure P 8) to close the

clamp jaws onto the track. Be sure that the clamp locking knob

is securely tightened before proceeding.

CAUTION:

Always use a ceiling wire hanger or equivalent material,

in addition to the clamp locking knob, to help secure

the laser level while mounting it to a wall. Thread the

wire through the handle of the laser level. DO NOT

thread the wire through the protective metal cage.

Additionally, screws may be used to fasten the bracket

directly to the wall as a backup. Screw holes

(Figure P 9) are located at the top of the bracket.

5. Using the base leveling knob (Figure P 2) approximate a level

position from the wall.

6. The tool can be adjusted up and down to the desired height for

working. While supporting the mounting base, loosen the locking

knob on the left side of the bracket (Figure P 1).

7. Turn the adjustment knob on the right side of the bracket (Figure

P 4) to move the laser level up and down to set your height.

Use the measuring scale (Figure P 7) to pinpoint your mark.

NOTE: It may be helpful to turn the power on and turn the

rotary head so that it puts a dot on one of the laser scales. The

DEWALT target card is marked at 1–1/2" (38 mm), so it may be

easiest to set the offset of the laser to 1–1/2" (38 mm) below

the track.

8. Once you have positioned the laser at the desired height, tighten

the locking knob (Figure P 1) to maintain this position.

Construction Grade Rod

DANGER:

NEVER attempt to use a grade rod in a storm or near

overhanging electric wires. Death or serious personal injury

will occur.

Some laser kits include a grade rod. The DeWALT Grade Rod is

marked with measurement scales on both sides and is constructed in

telescoping sections. A spring-loaded button actuates a lock to hold

the grade rod at various lengths.

The front of the grade rod has the measurement scale starting at the

bottom. Use this for measuring from the ground up when grading or

leveling jobs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE080GS Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info