Bedienungsanleitung Garmin BC 40 (Seite 8 von 14) (Englisch)

691049

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Pairing Additional Cameras with a Garmin

Navigation Device

You can pair up to 4 BC 40 wireless backup cameras with a

compatible Garmin navigation device.

Install batteries in the camera.

The camera enters pairing mode automatically, and the LED

flashes blue while the camera is in pairing mode. The camera

remains in pairing mode for five minutes. If pairing mode

expires, you can remove and reinstall the batteries.

Bring the compatible Garmin navigation device outside your

vehicle and within 1.5 m (5 ft.) of the camera, and turn on the

navigation device.

On the Garmin navigation device, select Settings > Wireless

Camera > Add New Camera.

The device pairs with your camera, and the guidance line

configuration screen appears.

Use the on-screen arrows to position the guidance lines, and

select (Aligning the Guidance Lines, page 5).

If the camera or vehicle is not ideally positioned to complete

the guidance line alignment, you can complete the alignment

later from the camera settings.

Enter a name for the camera (optional).

You should use a descriptive name that clearly identifies the

location of the camera.

Select Done.

After you pair multiple cameras, you can switch between

cameras from the camera view (Switching Cameras, page 4)

and set the order in which the cameras appear (Changing the

Camera Order, page 5).

Viewing the Backup Camera

After you pair your camera with a compatible Garmin navigation

device, the camera view appears automatically when you turn

on your navigation device, and you can manually show the

camera at any time.

• If your navigation device is connected to an ignition-switched

power outlet (recommended), turn on your vehicle.

• If your navigation device is connected to an always-on power

outlet, turn on the navigation device.

• To show the camera manually, select / .

• To show or hide the camera using voice commands, say

Show Video or Hide Video.

NOTE: The voice commands may vary based on your

navigation device model. This feature is not available for all

languages or may require additional navigation device setup

for some languages. For more information, see the Voice

Command app or the Voice Control app on your navigation

device, or the navigation device owner's manual.

The camera view appears. When the camera detects the vehicle

is moving forward, the camera automatically stops sending

video, and the navigation device returns to normal operation.

The camera video is dismissed automatically after 2 minutes

and 30 seconds, whether or not your vehicle has moved

forward.

Switching Cameras

You can cycle through the video feeds from all paired cameras.

From the camera view, select .

The video feed from the next camera appears, and the

camera name appears at the top of the screen.

Adjusting the Camera Angle

You can adjust the camera angle up and down to provide the

best view for your vehicle.

Drive to a level area with a clear view behind the vehicle.

Remove the camera from the mount (Removing the Camera

from the Mount, page 4).

Use a Phillips screwdriver to loosen the two adjustment

screws .

Tilt the mount up or down.

For most vehicles, the camera should face straight out or

slightly downward.

Tighten the adjustment screws to lock the mount in the new

position.

Install the camera into the mount.

View the camera using your Garmin navigation device

(Viewing the Backup Camera, page 4), and verify the camera

angle.

When the camera is angled correctly, the bottom edge of the

video frame should align with the rearmost part of the vehicle,

such as the bumper or trailer hitch. Objects above the

horizon should appear in the top one-quarter to one-third of

the frame.

If necessary, repeat this procedure until the camera angle is

correct.

WARNING

After you adjust the camera angle, you must align the guidance

lines (Aligning the Guidance Lines, page 5). If you previously

set up guidance lines, they are not accurate after the camera

angle changes. Failure to properly align the guidance lines could

result in an accident or collision, resulting in death, serious

injury, or property damage.

Removing the Camera from the Mount

Gently press the tab on one side of the mount outward,

and pull that side of the camera out of the mount.

Backup Camera Settings

Select Settings > Wireless Camera, and select the backup

camera name.

Flip Video: Allows you to flip or mirror the video.

Guidance Lines: Sets preferences for guidance lines displayed

on the camera video.

Rename: Allows you to rename the paired camera.

Set Default Camera: Sets the order in which cameras appear in

the camera view. The camera at the top of the list is the

4 Viewing the Backup Camera

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin BC 40 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin BC 40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info