Bedienungsanleitung Icon Image 6.0 EX - IMEVEX4715.0 (Seite 7 von 14) (Englisch)

654662

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

22 7

6. Turn the Seat Post Knob (20) counterclockwise two or

three turns to loosen it. Next, pull the Knob, raise the

Seat Post (8) a few inches, and then release the Knob.

Move the Seat Post up and down slightly until the

pin on the Knob snaps into one of the holes in the

Seat Post. Then, turn the Knob clockwise until it is

tight.

Attach the Seat Bracket (7) to the Seat Post (8) with

two M8 x 25mm Patch Screws (59). Make sure that

the Seat Bracket is oriented so the slot is on the

indicated side.

7. Attach the Seat (9) to the Seat Carriage (11) with four

M8 Nylon Locknuts (38) and four M8 Split Washers

(55). Note:

The Nylon Locknuts and Split W

ashers

may be preattached to the underside of the Seat.

Slide the Seat Carriage (1

1) into the Seat Bracket (7).

Move the Seat to the desired position. Insert the Seat

Knob (10) into the slot in the side of the Seat Bracket,

and tighten the Seat Knob into the Seat Carriage.

Slot

5. Have another person hold the Console (4) near the

Handlebar (3).

Connect the Upper Wire Harness (42) to the wire har-

ness on the Console (4). Locate the two ground wires

that are connected with a screw to the Handlebar (3).

Connect the two ground wires to the two smallest wires

on the Console. Next, locate the pulse wire extending

from the Handlebar. Connect the pulse wire to the

remaining wire on the Console. Then, snap the

Handlebar Cover (5) onto the Handlebar.

Carefully insert all excess wiring into the Console (4).

Attach the Console to the metal plate on the Handlebar

(3) with four M4 x 16mm Screws (57).

Be careful to

avoid pinching the wires.

Do not pinch

the wires during

this step.

Pulse

Wire

Ground

Wires

Inspect and properly tighten all parts of the exercise

cycle regularly. To clean the exercise cycle, use a

soft, damp cloth.

To prevent damage to the console,

keep liquids away from the console and keep the con-

sole out of direct sunlight.

HOW TO ADJUST THE DRIVE BELT

If you can feel the pedals slip whilst you are pedaling,

even when the resistance is adjusted to the highest

level, the drive belt may need to be adjusted. To

adjust the drive belt, you must first remove the Right

Side Shield (27). Using an adjustable spanner, turn

the Right Pedal (21) counterclockwise and remove it.

Next, remove the indicated M4 x 25mm Screws (58).

Turn the Right Crank Arm (23) so it is pointing toward

the front of the exercise cycle, and then slide off the

Right Side Shield.

Next, turn the indi-

cated M8 Nylon

Locknut (38) until

the Drive Belt (47)

is properly tight-

ened. Then, reat-

tach the right side

shield.

PULSE SENSOR TROUBLESHOOTING

If the handgrip pulse sensor does not function properly,

see step 5 on page 12.

MAINTENANCE AND TROUBLESHOOTING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Icon Image 6.0 EX - IMEVEX4715.0 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Icon Image 6.0 EX - IMEVEX4715.0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info