Bedienungsanleitung Line 6 POD HD500X (Seite 10 von 18) (Englisch)

693636

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Editing Amp, Cab & Mic Parameters

WhenanAmpBlockisselected,youcanusetheMulti-functionknobs

1-4toselectAmp,Cabinet,orMicModels.Whenusingadualamp

setup,Knob4allowsyoutoassignwhichampgetscontrolledbythe

DRIVE, VOLUME, and TONE knobs.

Amp Block OFF

Turn any of the Amp Tone knobs to adjust the desired settings for the

selected Amp.

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

SAVE

HOLD FOR SYSTEM & I/O

VIEW

Whenever you adjust any of the Amp Tone knobs, you’ll see the

“Momentary”AMP: EDIT LCD screen temporarily displayed, showing the

actualvaluesoftheToneknobsforbothcurrentAmpA&AmpBModels.

Or, to manually display the AMP:EDIT screens, double-press the ENTER

buttonwhenanAmpModelisselected.You’llseethescreen’srespective

controls adjust as you adjust the DRIVE, VOLUME, and TONE knobs.

The black “dots” around each knob indicate its last-saved value. With an

AmpBlockoyou’llseeonlyaVOLknob.Thisisaseparateparameter

strictly for the Amp Model’s Bypass Volume. Use the VOLUME knob

on your device to adjust this, and its value is stored separately with the

Preset for whenever the Amp Block is Bypassed.

YoucanusetheAmpModeldeepeditparameterstocompletelychange

the behavior of any amp model from subtle to extreme. It's like having your

very own amp techinician by your side. From page 1 of the AMP:EDIT

screen, press the 4 Way Nav Pad right arrow button to view page 2.

Knob 1 - MASTERsetstheamountofpowerampdistortion.Thispa-

rameter is highly interactive with all deep edit parameters.

Knob 2 - SetstheamountofSAGinthepoweramp.Athighersettings

the model becomes "squishy" with more touch sensitivity and improved

sustain.

Knob 3 - Controls how much heater hum and AC ripple interacts with

your tone. At maximum setting things get really freaky - you've been

warned.

Knob 4 - Sets the Multi-Function knobs to alter the settings on this

page for Amp A or Amp B.

Press the 4 Way Nav Pad right arrow button again to view page 3.

Knob 1 - Adjusts the bias of the power tubes. At maximum the amp is op-

erating in Class A. Set to minimum you get a very "cold" Class AB biasing.

Knob 2 - Bias Excursion is a phenomenon that occurs only as the

power tubes are pushed. Set low for a tighter feel. Set high for more

tube compression (Note: Turn DRIVE&MASTERuptoexperiencethis

phenomenon).

Knob 4 - Sets the Multi-Function knobs to alter the settings on this

page for Amp A or Amp B.

Press the 4 Way Nav Pad right arrow button one more time to view page 4.

Knob 1 - Sets the amount of "early reﬂections." Higher settings add more

reﬂective room sound to your tone.

Knob 2 - Turn to change Cabinet Models .

Knob 3 - Selects Microphone type.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Line 6 POD HD500X Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Line 6 POD HD500X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info