Bedienungsanleitung Multiplex ROYALevo12 (Seite 17 von 57) (Englisch)

30266

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

ROYAL evo

Page 72

9.3. Security queries when switching ON

9.3.1. Throttle check

If in the menu L Transmitter the parameter Check

thr. is ON (è 13.1.6.), the following can appear:

The transmitter starts immediately and RF radiation

begins.

For safety reasons throttle is kept in idle until the

throttle control (Heli: throttle limiter) is in idle posi-

tion (Heli: at throttle minimum).

The symbol below the text reminds you of the

control, used for throttle. The figure above shows

the stick symbol.

If Throttle-Cut is active the transmitter immediately

starts operation and a message appears for 4 sec.:

ThrottleThrottle--Cut activeCut active

Also in this case the corresponding switch is indicated.

The “Throttle Check” safety query can be switched ON

or OFF as required (è 13.1.6.).

' TIP ! If the safety query does not disappear

When missing or defective operating elements are as-

signed for Throttle and Throttle Cut the safety query can

be by-passed by pressing any of the menu buttons or

ENTER.

9.3.2. RF Check with the synthesizer module

If a synthesizer RF module is fitted in your ROYALevo, an

additional safety query can be activated (Check RF).

When you switch ON with an HFM-S synthesizer RF

module fitted, the following screen may appear after

the power-on info screen:

For safety reasons RF transmission remains OFF until

you confirm the displayed channel or transmission fre-

quency by pressing any direct menu access button or

the ENTER button. Only then will you see the last active

status screen; RF transmission is then activated.

The “RF Check” safety query can be switched ON or OFF

as required (è 13.1.7.).

9.4. Selecting the channel with an HFM-S

synthesizer RF module

Channel selection with an HFM-S synthesizer RF module

is very simple, convenient and safe:

1. Switch on the transmitter with the tool button L

pressed in

⇒ You are now at the channel setting menu,

RF is OFF (LED glows constantly).

The following display appears:

Set the channel you wish to use by pressing the „s“(UP)

/ „t“(DOWN) buttons, or one of the two 3-D digi-

adjustors. The channel is displayed as a channel number

and also the associated transmission frequency. To

activate the transmitter on the channel you have just

selected, the transmitter must now be switched OFF,

and then switched on again -.

2. Switch the transmitter OFF and then ON again

(this time WITHOUT the tool button pressed in)

You will see the following display::

English text:

Channel 72

NEW CHANNEL!

Enable RF

For your information the screen displays the previously

set channel. RF transmission remains OFF (=> LED glows

constantly) until the waiting period (horizontal bar on

screen) to activate the new channel has elapsed. During

this waiting period you have the chance to switch off

the transmitter before the RF module is activated, if, for

example, you have inadvertently set the wrong channel.

When the waiting period has elapsed, the last used

status display appears

The LED starts flashing, the transmitter is ready for use.

9.5. The RF status display (red LED)

The red LED (light emit-

ting diode) constantly

indicates the current

status of the RF module

when the transmitter is

switched on, i.e. whether

an RF (Radio Frequency) signal is being transmitted or

not.

RF transmission ON: 2 sec 2 sec ...

The LED flashes at intervals of about 2 seconds and the

transmitter is ready for use.

RF transmission OFF:

The LED glows constantly.

The system monitors the current drain of the RF module

to check whether an RF signal is being transmitted or

not, rather than by checking the status of the RF mod-

ule. If the current drain is below a typical value, either

no RF signal is being transmitted, or the RF signal is

being transmitted at less than full power (in which case

safe operation cannot be guaranteed!) This method of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo12 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info