Bedienungsanleitung Multiplex ROYALevo12 (Seite 16 von 57) (Englisch)

30266

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Instructions

Page 71

9. Using the transmitter

9.1. Switching on for the first time

When you switch on the transmitter for the first time

the following display appears:

Use the buttons „s“ (UP) or „t“ (DOWN) to select your

language and confirm by pressing „ENTER“. The lan-

guage can be changed at any time (è 13.5.2.). All user-

definable names (like mixer names, assignment table

names, model names) are not affected if you change the

language.

9.2. The power-ON procedure

When the you switch the transmitter ON, the following

power-on info screen will always appear briefly, regard-

less of whether an RF module is installed or not. This

gives information on the transmitter type, the current

software version and the languages available for the

screen texts:

If no RF module is fitted, the following message appears

briefly: „Note: No RF!“

9.2.1. Switching ON with the

HFM-4 RF module for crystals

After the power-on info screen (è 9.2.), the last used

status display appears (è 9.6.). If everything is in order,

the software immediately activates the RF module for

crystals, and an RF (Radio Frequency) signal is immedi-

ately transmitted. The LED starts to flash, the screen

switches to the last active status display, and the trans-

mitter is ready to use.

9.2.2. Switching ON with the

HFM-S synthesizer RF module

After the power-on info screen (è 9.1.), the currently

set channel and transmission frequency appears briefly

for your information:

After this the last used status display appears. If every-

thing is in order, the software activates the synthesizer

RF module, and an RF (Radio Frequency) signal is im-

mediately transmitted. The LED starts to flash, the

screen switches to the last active status display, and the

transmitter is ready to use.

The first time you switch the transmitter ON with a syn-

thesizer RF module fitted, or after installing a different

synthesizer RF module, an information screen appears,

replacing the power-on info screen. This tells you how

to set the channel when using a synthesizer RF module:

The method of selecting a channel when using an HFM-

S synthesizer RF module is described in Section 9.4.

9.2.3. Switching on without transmitting an RF sig-

nal

Whether you are using an HFM-4 RF module for crystals

or an HFM-S synthesizer RF module it is possible to

switch the transmitter ON without transmitting an RF

signal, even when an RF module is installed. The trans-

mitter can then be operated in that mode. This can be

useful for programming when no RF signal is required,

e.g. to minimise current drain, or when your channel is

already in use.

Hold the tool button L pressed in when you switch the

transmitter on ⇒ you are now at the power-on menu.

RF is OFF (⇒ LED glows constantly)

The following display appears:

With

HFM-4 RF module

for crystals

With

HFM-S synthesizer

RF module

Pressing any direct menu access button, or the ENTER

button, takes you to the last active status display.

!! Note:

RF stays OFF until the transmitter is switched ON again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo12 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info