Bedienungsanleitung Multiplex ROYALevo12 (Seite 18 von 57) (Englisch)

30266

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Instructions

Page 73

monitoring is much safer, as it is also capable of detect-

ing faults and errors::

• Is an RF module installed?

• Is the connection between RF module and trans-

mitter in order (contact fault)?

• Is the RF module working correctly?

• Is a crystal fitted, and is it in order?

(only with HFM-4 RF module for crystals)?

• Is the transmitter aerial installed, and is it making

proper contact?

If the ROYALevo is in use as a Pupil transmitter, or in

diagnosis mode, no RF signal will be transmitted => LED

glows constantly.

9.6. The status displays

There are four different status displays available in total.

You can switch between the individual status displays at

any time (provided that you are at one of the other

status displays, i.e. not in a menu) using the „s“ or „t“

buttons, depending on the information you wish to see.

When you switch the transmitter on, the last used status

display will always appear.

Status display 1

Bars

Line 1 Status of the 3-D digi-adjustors.

Numerous set-up parameters can be assigned

to the 3-D digi-adjustors, which can then be

varied directly (è 10.2.2.).

Line 2 Current model memory with

No. of the memory (1): model name(BASIC)

Line 3 Current operating voltage of the transmitter

battery in numeric form, and also graphically

in horizontal bar form

Line 4 Version: ROYALevo 9 or ROYALevo 12

Line 5

User name (è 13.5.3.)

Line 6 Operating time of the

current model memory(è 17.1.)

Bars The 4 bars at the sides and bottom of the

screen show the current trim positions of the

4 primary control functions/sticks (è11.4.)

Status display 2 (flight phases)

Line 1 Status of the 3-D digi-adjustors, see above

Line 2 Current model memory, see above

Line 3 Current operating voltage, see above

Line 4 Code letter of the switch used to change

flight modes (è 18.4)

Line 5 Current flight mode with

No. (1): name (NORMAL)

Bars Current trim positions, see above

Status display 3 (Timers)

Only timers with assigned switches are displayed. Be-

hind the time the switch code letter is shown (P in the

example).

Line 1 Status of the 3-D digi-adjustors, see above

Line 2

Slot-Timer (è 17.2.)

Line 3

Sum Timer (è 17.3.)

Line 4

Interval Timer (è17.4.)

Bars Current trim positions, see above

Status display 4 (system)

Line 1 Variant (ROYALevo 9 or 12),

software-version (e.g. 9/23),

language set currently loaded (e.g. DE/GB)

Line 2 with synthesizer module: channel no. freq.

else type of RF module (HFM-4) or "No RF"

Line 3 Transmission system (FM-PPM 9)

Line 4 available battery charge

Line 5 residual operating time with the residual

charge at the current power consumption

Line 6 Overall operating time of the transmitter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo12 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info