Bedienungsanleitung Multiplex ROYALevo12 (Seite 24 von 57) (Englisch)

30266

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Instructions

Page 79

' TIP: Changing the assignment

If the default assignment of transmitter controls and

switches does not meet your requirements, you can

change the set-up at any time.

(è 13.3. L Setup, Assignment)

6. Leave the menu by selecting OK;

you have successfully created the new model.

Step •• Entering the model name

The model is assigned a name in the menu

I Memory/Properties (è 18.5.)

Step ŽŽ Connecting servos

Connect the servos, speed controller, ... to the receiver,

keeping to the sequence of receiver outputs described

in the model template. The receiver output sequence

can be checked in the menu K Servo/Assignment

(è 16.2.).

! Note:

If you wish to connect devices (servos, speed control-

lers, ...) designed for different signal formats, you can

change this parameter separately for each channel in

the menu K Servo/Assignment (è 16.2.).

' TIP:

In the same menu you can also change the assignment

of the receiver outputs if necessary (in sequence and/or

function).

Step •• Switch on transmitter and receiver

! Note the correct sequence when switching on!

Always switch on the transmitter first,

and only then the receiver.

! Caution!

Injury hazard: power systems may burst into life!

In principle you can now control your model, but in fact

you need to set up the various values to suit the model

in question.

Step •• Calibrating the servos

Please work with the greatest care when calibrating.

Your model will only respond accurately to the controls

if the servos are correctly calibrated.

The servos are calibrated in the menu

K Servo, Calibrate (è 16.1.).

Step ‘‘ Setting up mixers

The mixers are set up in the menu G Mixer. This menu

is dynamic in nature, i.e. in the interests of clarity the

screen only displays the mixers used in the current mo-

del. The values assigned to the mixers in the model

templates are default (standard) values, and they will

need to be adjusted to suit your model.

Please refer to Section è 15 for all you need to know on

the subject of setting up mixers.

Step ’’ Setting up the transmitter controls

The transmitter controls are set up in the H Control.

Like the Mixer menu, this menu is dynamic in nature, i.e.

in the interests of clarity the screen only displays the

transmitter controls used for the current model.

è 14.

Step ““ Pre-flight checks

Your newly created model is now ready to fly. Before

you operate the model for the first time be sure to test

all the working systems carefully.

You will probably need to fine-tune various aspects of

the control system, especially relating to mixers and

transmitter control settings, and this is done during the

test-flying process. Don’t be tempted to make changes

in a menu while the model is in the air. The safe, con-

venient method of altering values is to use the 3-D digi-

adjustor (è 10.2.2.).

Step ”” Activating flight phases

Once you have test-flown the model in one flight phase

(usually the Normal flight phase) and successfully

trimmed it out, with all the mixer and transmitter con-

trol values set to your satisfaction, you can consider

setting up additional flight phases (if you wish). Flight

phases enable you to optimise the model for use in

different flight situations. The first step is to activate a

new flight phase and copy the values from the first

flight phase into the newly activated phase (è 18.4).

The transmitter control settings can now be adjusted (H

Control menu) to suit the new task. All the transmitter

control settings marked with a small number (1 …4) can

be adjusted separately for each flight phase (è 14).

12.3. A new helicopter

!! Safety note

Radio-controlled model helicopters are technically de-

manding flying machines which require fastidious set-

ting up, maintenance and general care. If operated in-

competently or irresponsibly they represent a serious

hazard.

If you are a beginner we recommend that you:

• Contact an experienced model pilot, your local

model club or a model flying school, and ask for

help.

• Ask your local model shop for advice.

• Increase your knowledge by reading all you can

find on the subject.

Step ŒŒ Creating a new memory

New models are created by moving to the sub-menu

New Model in the I Memory menu (è18.6.).

This is the procedure once you have reached this menu:

1. The software automatically selects the first vacant

spot memory for the new model.

(Parameter Memory nr.)

2. You select a template to suit the model

(Parameter Template).

From the two available model helicopter tem-

plates select the one which is closest to your

model: see table on the next page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo12 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info