Bedienungsanleitung Multiplex ROYALevo12 (Seite 23 von 57) (Englisch)

30266

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

ROYAL evo

Page 78

11.3. The cruciform digital trim assembly

The trims of the ROYALevo take the form of buttons

arranged in a cross, located below and to one side of

the stick units. They are located in an ergonomically

optimum position, and can be reached easily when the

transmitter is hand-held or installed in a tray.

Each press of a trim button

effects a trim adjustment

around the corresponding

control axis in the direction

of that button.

If you hold a trim button

pressed in for longer than

about 1 second, the trim

continues to increment

until you release the but-

ton (AUTO-REPEAT).

Each trim step (increment) is accompanied by a confir-

mation beep. When you reach the trim centre position,

and when you reach the ends of the available trim ran-

ge, you will hear different sounds. You can switch the

trim beeps OFF if you prefer (è 13.1.2.).

The trim of the 4th stick axis (‡‡ ) always works

in idle trim mode for throttle!

This is also valid if SPOILER is assigned to this H

and for helicopters.

11.4. On-screen trim display

The trim settings are displayed on the screen in status

displays 1-3. They take the form of graphic displays in

bar form, on both sides and the bottom of the screen:

Starting from the trim centre position, a maximum of 20

trim steps are available in both directions. The trim in-

crements can be set to any of 4 values from 0.5% to

3.5% ( TStep è 14.2.3).

!! Note: Trim step width, trim range

When you alter the trim step, the number of

steps stays the same. This means that both the

trim range and the actual trim value (!) are

changed, i.e. you must adjust the trims again if

you alter the trim increment size.

The current trim value is displayed on the screen in

graphic form, but it can also be displayed numerically if

you wish (parameter Trim è 14.2.2)

There are several variations in the form of the graphic

trim display shown in the status display (parameter

Trim graph è 13.1.1)

' TIP !

Reset trim to centre

If you press both buttons for one of the trimmed axis

simultaneously, trim is set to centre for the currently

active flight phase. This applies also to throttle.

12. Creating a new model

12.1. Basic information

With the ROYALevo you create a new model by select-

ing a model template. A total of eight model templates,

or sample models, are available, sub-divided into fixed-

wing and helicopters (detailed description of model

templates è 12.4.):

1. BASIC 7. HELImech

2. ACRO 8. HELIccpm

3. HOTLINER

4. DELTA

5. GLIDER

6. 4 FLAPS

The values defined by the template serve as starting

points, and have to be adjusted to suit your model. All

the settings and definitions can be altered at any time

and changed in any way you wish.

" Take it in easy stages "

When you wish to create a new model with the

ROYALevo there are various ways you can proceed. In

our opinion the procedures described in the following

sections for fixed-wing models (è 12.2.) and helicop-

ters (è 12.3.) are the swiftest means of getting to your

destination.

12.2. A new fixed-wing model

Step ŒŒ Creating a new memory

New models are created by moving to the sub-menu

New Model in the I Memory menu (è18.6.).

This is the procedure once you have reached this menu:

1. The software automatically selects the first vacant

spot memory for the new model.

(Parameter Memory nr.)

2. You select a template to suit the model

(Parameter Template).

From the eight available model templates select

the one which is closest to your model (description

of model templates è 12.4.)

3. Choose the servo type and the servo assignment

(sequence) at the receiver.

(Parameter Servo conf.)

4. Select your preferred control mode (stick mode)

(Parameter Mode)

5. Select an assignment list (which transmitter con-

trols operate the various functions).

(Parameter Assignment)

! Note re. assignment list

In each case you must use the stated assignment

list (from the three lists available) depending on

the model template you have selected. If you do

not do this, the model template cannot be guaran-

teed to function as described in the text (è 12.4.).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo12 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info