Bedienungsanleitung Sangean U4D BT plus (Seite 6 von 16) (Englisch)

797387

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Powered via DC IN socket

The radio can be also powered via the DC IN socket

which can allow 12 Volt DC, which is designed to be

radio with you outdoors or on the boat.

An additional cigarette lighter cable is required (not

supplied) for this device.

NOTE

Never use the 12 Volt socket in rainy or moist conditions

to prevent moist from entering the radio. Always keep

the rubber cover on the back well closed under these

conditions.

NOTE

If no controls are used and no sound output from the

radio for 15 minutes, the radio will be put into standby

mode when using the mains power. When the radio is

operated on battery power, the radio will be switched off

completely in order to minimize battery usage.

Battery charging status indicator

Please note that the battery charging status detection

can only be activated when the radio is in charging mode

(i.e. the radio is switched off, the battery switch slides to

the NiHM position and it is connected to the AC mains

socket).

1. When charging is in progress,

display is shown at right and the

charging indicator ashes yellow.

2. When the charging process is

completed, the charging indicator

lights in steady yellow.

If batteries are already fully charged, display is

shown at right and it will switch to standby mode after 5

seconds.

3. When there is no battery / missing

batteries in the compartment or

some of batteries are inserted

with the incorrect polarity, display is shown at right

and it will enter standby screen after 5 seconds.

NOTE

If a battery is removed while charging, display is

shown at right and the charging indicator lights red.

4. During the charging process, if a

battery is detected as faulty /

damaged, a solid square will be

displayed under the corresponding battery number (see

picture, right) and the charging indicator ashes red.

UsingDABforthersttime–DAB

1. Straighten up the antenna.

2. Press the Power button to switch on the radio. If the radio

has been used before the last used mode will be selected.

3. Press and release the Source button to select DAB

mode. The display will show DAB for a few seconds.

4. If this is the first time the radio is used a quick scan

of the DAB Band III channels may be carried out. The

display will show ‘Scanning’ (If the radio has been

used before the last used station will be selected

instead.) During the scanning process, as new stations

are detected the station counter will increase and the

stations will be added to the list which is stored in the

radio. The bar graph indicates the progress of the scan.

5. When scanning is completed the radio will list the

stations found (in numeric-alpha order 0....9...A...Z),

unless it has previously been tuned to a DAB station.

Rotate the Tuning control to scroll through the list of

available DAB radio stations. Press the Tuning control

to select the highlighted station. When a DAB station

is found, the display will show the station name on the

upper line of the text display and broadcast information

on the lower line. Use the Volume control to set the

sound level as needed.

6. If the station list is still empty after the scan the display

will show ‘No DAB Station’ then return to the DAB

menu. If no stations are found it may be necessary to

relocate your radio to a position giving better reception.

Selectingastation–DAB

1. When playing a DAB radio station, the display normally

shows the name of the current station with other related

information.

2. Rotate the Tuning control to access the radio station

list and scroll through the available stations.

3. Press the Tuning control to select the desired station.

4. Use the Volume control to set the sound level as needed.

If the display shows 'Service Not Available' it may be

necessary to relocate your radio to a position giving

better reception.

A question-mark in front of the station name merely

indicates that the station has not recently been detected

by the radio. It may still be available.

NOTE

Secondaryservices–DAB

1. Certain radio stations may have one or more secondary

services associated with them. If a station has a

secondary service associated with it the display will

show “>>” next to the station name on the station list.

The secondary service will then appear immediately

after the primary service as you rotate the Tuning

control.

2. Press and release the Tuning control to select the

station. Most secondary services do not broadcast

continually and if the selected service is not available,

the radio will re-tune to the associated primary service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sangean U4D BT plus Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sangean U4D BT plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info