Bedienungsanleitung Visonic Powermaster-360 (Seite 25 von 96) (Englisch)

769323

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

D-307500 PowerMaster 360 Installer's Guide 25

Select MODIFY

DEVICES Option

[1]

Select the respective

device Group

[2]

Select exact device

you require to modify

[3]

Select the Parameter

you require to modify

[4]

Modify the

Parameter



02:ZONES DEVICES

CONTACT SENSORS



MODIFY SENSORS

MOTION SENSORS

Z10:Motion Camra

ID No. 140-1737

Z10:LOCATION

Z10:ZONE TYPE

Z10:SET CHIME

Z10:PARTITIONS

Z10:DEV SETTINGS

See  [4]

When

done  to

step 2



– Modifying or Reviewing a Device

[1]

Enter the Installer Mode menu, select the 02:ZONES/DEVICES option (see section 4.2) and then select the

MODIFY DEVICES option.

[2]

Select the respective group of the device you require to review or modify. For example, MOTION SENSORS.

[3]

Scroll the Device Group, identify (by zone and/or ID number) of the exact device you require to modify or review, for

example: Z10:Motion Camra > ID No. 140-1737.

[4]

From here on the process is same as the configuration process that follows the enrollment of that device. To

continue, refer to Section 4.4.2 Adding a New Wireless Device Part B. When done, the display will show the next

device of the same type (i.e. Motion camera).

4.4.5 Replacing a device

Use this option to replace a faulty device that is enrolled in the system with another device of the same type number

(i.e. same first 3 digit of the ID number – see section 4.4.2.A) while keeping the same configuration of the original

device. There is no need to delete the faulty device or to reconfigure the new device. Once enrolled, the new device will

be configured automatically to the same configuration of the faulty (replaced) device.

To replace a device proceed as follows:

Step 1



Step 2



Step 3



Step 4



Step 5

Select REPLACE

DEVICES Option

[1]

Select the respective

device Group

[2]

Select exact device

you require to replace

[3]

Enroll the new device

[4]



02:ZONES/DEVICES

CONTACT SENSORS



REPLACE DEVICES

KEYFOBS

K03:Keyfob

ID No. 300-0307

ENROLL NOW or

ENTR ID:300-XXXX

See 

[4].



– Replacing a Device

[1]

Enter the Installer Mode menu, select the 02:ZONES/DEVICES option (see section 4.2) and then select the

REPLACE DEVICES option.

[2]

Select the respective group of the device you require to replace. For example, KEYFOBS.

[3]

Scroll the Device Group, identify (by zone and/or ID number) the exact device you require to replace, for example:

K03: Keyfob > ID No. 300-0307.

If you try to enroll a new device of a different type than the replaced device, the PowerMaster-360 will reject the

new device and the Virtual Keypad display will read WRONG DEV.TYPE.

When complete, the Virtual Keypad display shows the device details of the new device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic Powermaster-360 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info