Bedienungsanleitung Visonic Powermaster-360 (Seite 29 von 96) (Englisch)

769323

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

D-307500 PowerMaster 360 Installer's Guide 29

4.5.2 Configuring arming/disarming and exit/entry procedures

The following table provides you with a detailed description of each option and its configuration settings. To select an

option and change its configuration – refer to section 4.5.1.

Option

Configuration Instructions

01:ENTRY DELAY1

02:ENTRY DELAY2

Two different entry delays allow the user to enter the protected site (while the system is in the

armed state) via dedicated exit/entry doors and routes without causing an alarm.

Following entry, the user must disarm the control panel before the entry delay expires. Slow-

rate warning beeps start sounding via the Configuration device (PC or mobile) once the door is

opened, until the last 10 seconds of the delay, during which the beeping rate increases. The

ENTRY DELAY 1 and ENTRY DELAY 2 options allow you to program the time length of these

delays.

Options: 00 seconds; 15 seconds (default for entry delay 2); 30 seconds (default for entry

delay 1); 45 seconds; 60 seconds; 3 minutes and 4 minutes.

Notes:

1. In some PowerMaster-360 variants, these menus are displayed in the Operation

Mode only (see section 4.14).

2. To comply with EN requirements, the entry delay must not exceed 45 sec.

03:EXIT DELAY

This option allows programming the time length of the exit delay. An exit delay allows the user

to arm the system and leave the protected site via specific routes and exit/entry doors without

causing an alarm. Slow-rate warning beeps start sounding via the Configuration device (PC or

mobile) once the arming command has been given, until the last 10 seconds of the delay,

during which the beeping rate increases.

Options: 30 seconds; 60 seconds (default); 90 seconds; 120 seconds, 3 minutes and

4 minutes.

04:EXIT MODE

The Exit Delay time can be further adjusted according to your preferred exit route. The control

panel provides you with the following Exit Mode options:

A: normal - The exit delay is exactly as defined.

B: restrt+arm home - Exit delay restarts when the door is reopened during exit delay. If no

door was opened during exit delay AWAY, the control panel will be armed HOME.

C: restart>reentry - The exit delay restarts when the door is reopened during exit delay. The

restart occurs once only. Restarting the exit delay is helpful if the user re-enters

immediately after going out to retrieve an item that he left behind.

D: end by exit - The exit delay expires (ends) automatically when the exit door is closed even if

the defined exit delay time was not completed.

Options: normal (default); restrt+arm home; restart>reentry and end by exit.

Note: In some PowerMaster-360 variants, this menu is displayed in the Operation Mode only

(see section 4.14).

05:QUICK ARM

Define whether or not the user will be allowed to perform quick arming or not. Once quick

arming is permitted, the control panel does not request a user code before it arms the system.

Options: OFF (default) and ON (default in USA).

06:BYPASS ARM

Define whether or not the user will be allowed to manually bypass individual zones, or allow

the system to perform automatic bypassing of open zones during the exit delay (i.e. force arm).

If a zone is open and forced arming is not permitted, the system cannot be armed and NOT

READY is displayed. If no bypass is selected, neither manual bypassing nor force arming is

allowed which means that all zones must be secured before arming.

Options: no bypass (default); force arm and manual bypass (default in USA).

Notes:

1. To comply with EN requirements, "manual bypass" must be selected.

2. The option force arm is not applicable in the UK.

3. A zone in Soak Test mode that is configured as bypass will trigger a test fail event if

the system detects a potential alarm event.

4. There is no limit of reported events when a bypass zone is in Soak Test mode.

07:LATCHKEY ARM

When ON, a latchkey message will be reported by SMS message to users (see Note) upon

disarming by a latchkey user (users 5-8 or keyfob transmitters 5-8). This mode is useful when

parents at work want to be informed of a child’s return from school.

Options: OFF (default) and ON.

Note: To enable the reporting, you must configure the system to report alrt events to Private

users (Latchkey belongs to the alerts group of events). Refer to section 4.6.4 REPORTED

EVENTS option in both

VOICE REPORT

SMS REPORT

menus.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic Powermaster-360 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info