Bedienungsanleitung Visonic Powermaster-360 (Seite 30 von 96) (Englisch)

769323

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

30 D-307500 PowerMaster 360 Installer's Guide

Option

Configuration Instructions

08:DISARM OPTION

Certain regulations require that when the system is armed in AWAY mode, it may not be

disarmed from the outside of the house (such as by keyfobs) before entering the protected

premises and activating an Entry Delay zone. To answer this requirement, the PowerMaster-

360 provides you with the following configurable options to disarm the system:

A: At any time (default), the system can be disarmed at all times from all devices.

B: During entry delay, the system can be disarmed only using keyfob or prox operated devices

(on entry wrless).

C: During entry delay by code, the system can be disarmed only using the Configuration device

(PC or mobile) (entry + away kp.).

D: During entry delay, the system can be disarmed using keyfobs or by code using the

Configuration device (PC or mobile) (on entry all.).

Note: In some PowerMaster-360 variants, this menu is displayed in the Operation Mode only

(see section 4.14).

09:ARMING KEY

Determine that, when activated, the Arming Key will arm AWAY or HOME.

Options: arm AWAY (default) and arm HOME.

4.5.3 Configuring zones

The following table provides you with a detailed description of each option and its configuration settings. To select an

option and change its configuration – refer to section 4.5.1.

Option

Configuration Instructions

21:SWINGER STOP

Define the number of times a zone is allowed to initiate an alarm within a single

arming/disarming period (including tamper & power failure events of detectors, etc.). If the

number of alarms from a specific zone exceeds the programmed number, the control panel

automatically bypasses the zone to prevent recurrent siren noise and excessive reporting to the

Monitoring Station. The zone will be reactivated upon disarming, or 8 hours after having been

bypassed (if the system remains armed).

Options: after 1 alarm (default); after 2 alarms (default in USA); after 3 alarms and no stop.

Note:

When a detector is in Soak Test1 mode and also set to bypass, Swinger Stop will not

prevent the sending of events. This may result in excessive reporting of Soak Fail

events.

22:CROSS ZONING

Define whether cross zoning will be active ON or inactive OFF (default). Cross zoning is a

method used to counteract false alarms – an alarm will be initiated only when two adjacent

zones (zone couples) are violated within a 30-second time window.

This feature is active only when the system is armed AWAY and only with respect to the

following zone couples: 18+19, 20+21, 22+23, 24+25, 26+27.

Notes:

1. If one of the two crossed zones is bypassed (see Section 4.5.2), the remaining

zone will function independently.

2. It is recommended that crossed zones will be only zones used for detection of

burglary i.e. Zone Types: Entry/ Exit, Interior, Perimeter and Perimeter follower.

3. If a cross zone is in Soak Test mode, then each zone of this zone couple functions

independently.

Important! Do not define cross zoning to any other zone types such as Fire,

Emergency, 24h audible, 24h silent etc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic Powermaster-360 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info