Bedienungsanleitung Visonic Powermaster-360 (Seite 31 von 96) (Englisch)

769323

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

D-307500 PowerMaster 360 Installer's Guide 31

4.5.4 Configuring alarms and troubles

The following table provides you with a detailed description of each option and its configuration settings. To select an

option and change its configuration, refer to section 4.5.1.

Option

Configuration Instructions

31:PANIC ALARM

Define whether or not the user will be allowed to initiate a Panic Alarm from keypads (by

simultaneously pressing the two Panic buttons) or keyfobs (by simultaneously pressing the

Away and Home buttons), and whether the alarm will be silent (that is, only reporting of the

event) or audible (that is, the sirens will also sound).

Options: audible (default); silent and disabled.

32:DURESS ALARM

(not applicable in UK)

A duress (ambush) alarm message can be sent to the Monitoring Station if the user is forced to

disarm the system under violence or menace. To initiate a duress message, the user must

disarm the system using a duress code (2580 by default).

To change the code, enter the new 4-digit of the new Duress code at the position of the

blinking cursor or enter 0000 to disable the duress function and press .

Notes: The system does not allow programming a duress code identical to an existing user

code.

33:INACTIVE ALRT

Previously known as

NOT ACTIVE

If no sensor detects movement in interior zones at least once within the defined time window,

an inactive alert event is initiated.

Define the time window for monitoring the lack of motion.

Options: disabled (default); after: 3/6/12/24/48/72 hours

34:TAMPER ALARM

Define whether the Tamper switch protection of all zones and other peripheral devices (except

the control panel) are active (default) or not active.

Warning!: If you select

not active

, be aware that no alarm or report will be initiated in case of

tampering with any of the system peripheral devices.

35:AC FAIL REPRT

To avoid nuisance reporting in case of short interruptions in the house of AC power, the

system reports an AC Fail message only if the AC power does not resume within a pre-

determined time delay.

Options: after 5 minute (default), after 30 minute, after 60 minute or after 3 hours.

Note: To comply with EN requirements, the time delay must not exceed 60 min.

36:CONFIRM ALARM

Previously known as

CONFIRM TIME

If two successive alarm events occur within a specific time window, the system can be

configured to report the second alarm event as a confirmed alarm (see section 4.6.3 option

61). You can activate this feature and set the respective time window.

Options: disable (default in USA); in 30/45/60 (default)/90 minutes

Note: In some PowerMaster-360 variants, this menu is displayed in the Operation Mode only

(see section 4.14).

37:ABORT TIME

The PowerMaster-360 can be configured to provide a delay before reporting an alarm to the

Monitoring Station (not applicable to alarms from 24H SILENT and EMERGENCY zones).

During this delay period, the siren sounds but the alarm is not reported. If the user disarms the

system within the delay time, the alarm is aborted. You can activate the feature and select the

Abort Time interval.

Options: in 00 (default in USA)/15/30 (default)/45/60 seconds; in 2/3/4 minutes

Note: In some PowerMaster-360 variants, this menu is displayed in the Operation Mode only

(see section 4.14).

38:CANCEL ALARM

Previously known as

ALARM CANCEL

The PowerMaster-360 can be configured to provide a Cancel Alarm time window that starts

upon reporting an alarm to the Monitoring Station. If the user disarms the system within that

cancel alarm time, a cancel alarm message is sent to the Monitoring Station indicating that

the alarm was canceled by the user.

Options: not active (default in USA); in 1/5 (default)/15/60 minute(s) and in 4 hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic Powermaster-360 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info