Bedienungsanleitung Yamaha MOTIF ES7 (Seite 121 von 300) (Englisch)

571272

121

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

Quick Guide — Advanced Course

Creating a Song on the MOTIF ES

121

Owner’s Manual

Song Recording using Plug-in Voices

This section shows you how to use the Voices of an optional Single Part Plug-in Board (such as PLG150-AN, PLG150-PF

and PLG150-DX) in recording a Song.

1 ~ 4

Install a Single Part Plug-in Board to the

instrument, then follow steps #1 - 4 on page 75 to

set the necessary parameters.

In step #4, set PORT.NO (port number) to “2” or “3.”

Keep in mind that if you’ve also installed a PLG100-

XG Multi-Part Plug-in Board, the boards should be

set to different numbers.

5Enter the Song Play mode and call up the MIDI

output setting display ([SONG] →→

→→ [F3] TRACK →→

→→

[SF1] CHANNEL).

6Select the track for recording, making sure that

the track number is the same as that of the slot to

which the Plug-in Board is installed, and set the

port number.

The track number must match the slot number, and

the port number must be the same as set in step #4

above.

7Select a Voice of the installed Plug-in Board.

Enter the Mixing Edit mode ([MIXING] → [EDIT] →

Part selection). Press the [F6] button once or twice to

call up the display for the Plug-in Board parts (PLG

parts) as shown below (page 164). Next, press the

[TRACK SELECT] button (the lamp lights), and select

the PLG Part of Slot 1 by pressing the [1] button.

Finally, press the [F1] VOICE button, followed by the

[SF1] VOICE button, then select the desired Voice on

the Plug-in Board.

When you play the keyboard, you should be able to hear

the selected Voice of the Plug-in Board. If the Voice of the

Plug-in Board does not sound as expected, check the

following points.

●Make sure that the OUT CH of the track matches the

Receive Channel of the corresponding Part of the

tone generator.

Check the ReceiveCh (MIDI Receive Channel) in the

display called up by pressing the [SF2] MODE in the

above display, then check the OUT CH (MIDI Output

Channel) of track 1 in the display shown in step #6.

These two channels should be same.

●Make sure that the destination tone generator is set

to internal, not external.

Check the settings in the display called up via the [F1]

PLAY → [SF2] OUT CH button. The INT SW of the

corresponding track (1 in this case) should be set to

“on.”

8Record your keyboard performance using the Plug-

in Voice to track 1.

9Store the Song Mixing settings in the [SONG] →→

→→

[MIXING] →→

→→ [STORE] display (page 131).

The settings related to the Plug-in Board voice should

be stored as Song Mixing data.

10 Save the created Song data to a SmartMedia/USB

storage device (page 131) before turning the

power off.

nThe explanations above apply also to the Pattern modes.

TIP

When a Single Part Plug-in Board has been installed to

slot 1, move the cursor here then set the port number.

When a Single Part Plug-in Board has been installed to

slot 1, move the cursor here then set the port number.

Voice Bank

Voice Number

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF ES7 Seite 121

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF ES7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info